M2

3D Print Removal Tool - Scraper Includes: Scraper (1 pcs) Length: 175mmBlade width: 39mm

  4010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 40x40x10mmLocation: Extruder or electronics caseLength: Micro-Fit 3.0 43020 Fits: M2 (12 volt version) This is the...

  4010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against incorrect plug-in. All fans should be kept free of...

  5010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 50x50x10mmLocation: ExtruderConnector: Micro-Fit 3.0 43020 Fits: M2 (12 volt version) Mounted at a 45 degree angle in...

  5010 Extruder Fan for MakerGear M2 Dual Extruder - 24 volt  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: ExtruderConnector: Micro-Fit 3.0 43020Fits: M2 Dual Extruder  This fan has longer...

  5010 Extruder Fan for MakerGear M2 - 24 volt Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (24 volt version) Mounted at a 45 degree angle in front of the extruder's 40mm fan, this 50 mm...

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available separately here

  Bed Spring - M2 older version bed - 3 Pack Includes: Spring (3 pcs) Fits: MakerGear M2 (that have a 3 point bed with springs).

MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3 

Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotside and coldside. Contains high purity Boron Nitride and proprietary binders which reduce cracking and flaking when dried...

Brim Scraper (Mini Scraper) We find this tool handy for removing the brim, and purge lines from the build plate. Includes: Brim Scraper (1 pcs)

3D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

  Extruder Stepper Motor for MakerGear 3D printers Includes:1.8° stepper motor basePinion gear (installed) Fits:M2M3 Note: Does not include the 5.16:1 planetary gearbox.

  MakerGear Extruder Motor Comes assembled Includes:1.8° stepper motor base with pinion gear (1 pcs)Mated 5.16:1 gearbox with shaft (1 pcs) Note: Does not include the filament drive gear. Gear sold separately here.

  Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries- Expandable and rubber-coated- Suitable for both the V4...

MakerGear Filament Drive Gear Replacement This gear drives the filament through the extruder. Fits: M2M3-SEM3-ID

PB Select™ Filament Guide Tube for MakerGear Includes: Guide tube (1 pcs) Fits:M2M3

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

  8x10 Build Surface for MakerGear Printers Made from borosilicate glass, this 8"x10"x0.13" (20cm x 25 cm x 3.3 mm) comes standard with a sheet of polyimide tape already applied. Includes: Glass print surface (1 pcs)Polyimide tape (1...

PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm