M2

3D Print Removal Tool - Scraper Includes: Scraper (1 pcs)

  4010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 40x40x10mmLocation: Extruder or electronics case Fits: M2 (12 volt version) This is the smaller of the two fans mounted in front...

  4010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against incorrect plug-in. All fans should be kept free of...

  5010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (12 volt version) Mounted at a 45 degree angle in front of the extruder's 40mm fan, this...

  5010 Extruder Fan for MakerGear M2 Dual Extruder - 24 volt  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 Dual Extruder  This fan has longer leads to accommodate the M2 Dual 3D...

  5010 Extruder Fan for MakerGear M2 - 24 volt Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (24 volt version) Mounted at a 45 degree angle in front of the extruder's 40mm fan, this 50 mm...

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available separately here

  Bed Spring - M2 older version bed - 3 Pack Includes: Spring (3 pcs) Fits: MakerGear M2 (that have a 3 point bed with springs).

MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3 

Boron Nitride Thermal Paste (BN Paste) Thermal paste improves heat conduction and heat distribution in the hotside and coldside. Contains high purity Boron Nitride and proprietary binders which reduce cracking and flaking when dried...

Brim Scraper (Mini Scraper) We find this tool handy for removing the brim, and purge lines from the build plate. Includes: Brim Scraper (1 pcs)

3D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

  Extruder Stepper Motor for MakerGear 3D printers Includes:1.8° stepper motor basePinion gear (installed) Fits:M2M3 Note: Does not include the 5.16:1 planetary gearbox.

  Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries- Expandable and rubber-coated- Suitable for both the V4...

MakerGear Filament Drive Gear Replacement This gear drives the filament through the extruder. Fits: M2M3-SEM3-ID

PB Select™ Filament Guide Tube for MakerGear Includes: Guide tube (1 pcs) Fits:M2M3

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm

Slice Engineering Copperhead™ Heat Break for MK10 Bimetallic Heat Break™ - Stainless steel and Copper AlloyRated to 450 °C For more documentation on the Copperhead™ Heat Break, please see the Technical Specifications...

PB Select™ Black Heatsink for Nema17 Stepper Motor Heatsink in black anodized aluminum to remove heat from desired component.Equipped with self-adhesive on the back for easy attachment. Includes: Heatsink (1 pcs) Size: 40x40x10 mm