MK2.5

Needle File Set  Files with different profiles: flat, square, triangular, lenticular, semicircular, roundmade of GCr15 bearing steel Includes: Files (6 pcs)

Nozzle Cleaning Needle 0.3mm Diameter Includes: needle (5 pcs)  

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

PB Select™ Preset Torque Wrench  Includes:Preset Torque wrench (1 pcs)Bit holder FDM printed in POP Green ASA (1 pcs)1/4 inch socket adapter (1 pcs)6mm socket (1 pcs)7mm socket (1 pcs)8mm socket (1 pcs) Notes:Use on a clean...

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D, Nextruder Etc)5.5 mm5.0 mm4.5 mm (Sidewinder X3/X4) Fits:E3D V6 NozzlesPrusa Nextruder standard and highflow nozzles7mm RepRap...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

Prusa PEI-Ultem sheet Notes: 1. This is NOT the Spring steel sheet with smooth double-sided PEI.2. Tiny dots may appear on the PEI-Ultem surface. These can slightly affect the finished print bottom surface. However, they do not...

BuildTak PEI Sheet Includes: PEI sheet (2 pcs) Size: 228x254mm (9x10 inches)  An ideal print surface for the Original Prusa i3 MK2 and other 9x10 print beds. Manufactured in the USA to ensure consistent quality, the BuildTak...

PEI Print Surface - 260x242mm Includes: PEI sheet with 3M adhesive backing (1 pcs) Notes:1. This is NOT the Prusa spring steel sheet with smooth double-sided PEI (Link).2. Tiny dots may appear on the PEI surface. These can slightly...

PB Select™ Prusa Compatible V2 P.I.N.D.A Probe Includes: V2 PINDA (1 pcs) Fits:MK2.5MK2.5SMK3MK3S To test your current PINDA probe, follow this guide from the Prusa Knowledge Base.

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

  Prusa Brass Nozzle Brush Prusa Brass Nozzle Brush is optimized for 3D printing with its short and dense bristles. Includes: Brush (1 pcs) Made in EU with locally sourced beech wood.

PB Select™ Prusa PSU Holder Nut - 2 Pack Nickel plated M3nE nut. Used to secure the PSU to the t-slot rail. Includes: M3nE Nut (2 pcs) Fits:Prusa MK2.5Prusa MK2.5SPrusa MK3Prusa MK3SPrusa MK3S+Prusa MINIPrusa MINI+ To replace this part, please...

PB Select™ Filament Sensor Cover PTFE Tube for Prusa 3D Printers This is the replacement PTFE tube for filament sensor cover plastic part. It is ONLY compatible with the MK2.5 and MK3.  Includes: PTFE tube for filament sensor cover...

Prusa Hotend PTFE Tube Includes: Hotend PTFE tube (1 pcs) Specifications:Length: 50 (tolerance +/- 0.2 mm)Inner diameter: 1.85 mmOuter diameter: 4 mm Fits:MK2MK2SMK2.5MK3MMU2 Note: Not compatible with the MK2.5S, MK3S, MK3S+ or MMU2S...

E3D 4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth. These are the small collets that fit E3D V6 and Prusa heatsinks. Includes: Collet (1 pcs)  Size:ID: 4mmOD: 5mm Fits: Bondtech ExtrudersE3D V6...

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench (1 pcs) For:E3D V6Prusa i3RepRap

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...