Printer Parts

Panasonic Automotive Relay 20A 24VDC 1 FORM A BRACKET Manufacturer: Panasonic Coil Voltage: 24 VDC Relay Contact Form: 1 Form A (SPST-NO) Contact Current Rating: 20 A Coil Resistance: 320 Ohms Coil...

DC Barrel Plug with Cord Plug: 5.5x2.1mm - Right Angle  Wire: 22AWG Wire Length: 1.5 Meter    

Adjustable DC-DC  Boost Converter XL6009 Module These boost converters are great to use in conjunction with our power tool battery adapters. Includes: XL6009 Converter (1 pcs) Specifications:Input Range: 3V - 32VOutput Range: 5V -...

DDX Adapter For Copperhead™ Screw Mount To use with: Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Copperhead™ hotend with screw mount heat sink on a DDX Upgrade Kit

DDX Adapter For Microswiss All-Metal Use a Microswiss All Metal hotend with the Bondtech DDX. Part is SLS printed in PA12 (Nylon) Requires DDX extruder v2 or later. This part is necessary to install a Microswiss All Metal hotend on a DDX Direct...

DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10 S4 CR-10 S5 Requires your printer to have a 40x40x10mm...

DDX Bed Rod Holder Set for Ender-5 Plus Use the whole print surface of the Ender-5 Plus with this accessory Strong Plastic Parts made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature...

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included

DDX v2 Rear Housing For owners of DDX v1 units only This housing allows you to use a Micro Swiss all metal hotend in your DDX V1.SLS made part using Polyamide 12 (Nylon).

DDX v3 Adapter Set For Creality CR-10v2 and Cr10v3 Please Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatible with DDX v3, now even easier to install Fit a Direct Drive eXtruder on...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch bracket needed Creality CR-10 Max * - BLTouch bracket...

DDX v3 Adapter Set For Creality Ender and CR-10 Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatibility Table To use with 40x40x10 fans on: Creality Ender-3 Ender-3 v2 Ender-3...

Digital Calipers Kinex 150mm (Kinex is now K-MET) Features:Measuring length: 150mm/ 6in0,01mm resolutionmm/in toggle buttonKeeps measured value after turning offDIN 862, ČSN EN ISO 13385-1 Includes: Digital calipers (1 pcs)Plastic case (1...

Microswiss Lightweight Direct Drive Extruder with All Metal Hotend Scroll to the bottom of this page for setup instructions.   Important Note There has been an extruder stepper motor update on Creality machines. Before...

Microswiss Lightweight Direct Drive Extruder (Extruder Only Version) This is the "extruder only" version and does not include a hotend. The Microswiss All Metal Hotend is available for purchase here  Important Note There has been an...

Microswiss Lightweight Direct Drive Extruder with All Metal Hotend This version includes a Microswiss All Metal Hotend. The "Extruder Only" version is available for purchase here.  Important Note There has been an...

Dock Pin for Prusa XL Includes: Pin (1 pcs) Fits: Prusa XL To replace this part, please visit the Prusa knowledge base at help.prusa3d.com

  Door for Build Plate Ribbon Cable Access This is the small plastic door that goes on the bottom of the build plate where the ribbon cable is located.   Includes: Door (1pcs) Fits: Adventurer 4

  Flashforge Door Detection Board Senses when door is closed Includes: Detection board (1 pcs) Fits:Creator 3Inventor 2

Prusa Door Hinge Set Includes: Door-hinge-out (1 pc)Door-hinge-in (1 pc)Pin 2x40 (1 pc) Fits: Prusa CORE One To replace this part, please visit the Prusa knowledge base at help.prusa3d.com