Robo R1

Robo R1+ SD Card Bracket  Includes: Bracket (1 pcs) Fits:Robo R1Robo R1+   

Robo R1+ Spool Holder  Includes: Spool holder (1 pcs) Fits:Robo R1Robo R1+  Note: These are new, but this recent batch is older stock that has minor scuffing from storage.

Nema17 Stepper Motor for Robo R2 and C2 3D Printers Includes:Motor (1 pcs)Filament drive gear - installed (1 pcs) Fits: Robo R2Robo C2*Robo R1/+ (X/Y Axis Only) **Notes: This motor will work for the X and Y axis of all the above printers...

Nema17 Stepper Motor For the X/Y and Extruder axis of the R1/+, R2 and C2 3D printers. Includes: Motor (1 pcs) Fits:Robo R2Robo C2Robo R1Robo R1+

Super Lube® 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality grease...

Super Lube® 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease. Includes: 1...

4 Position, 90 Degree Right Angle, Terminal Block Header Includes: Header (1 pcs) Amps: 12Pitch: 5.08mm  

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:2 position20 ampSafety approval:  Shade of green may be different than photo

Terminal Block Plug 5.08mm Includes: Plug (1 pcs) Specs:4 position15 amp

4 Position Vertical Terminal Block Header Includes: Header (1 pcs) Amps: 12Pitch: 5.08mm

PB Select™ Thermistor for Robo R1  Item may vary slightly from photo, but will function the same. Robo 3D R1+ replacement thermistor Note: It helps to use a zip tie to hold the thermistor wire close to the extruder or use this...

Power Rocker Switch  Includes: Switch (1 pcs) 6A 250V AC10A 125V AC Compatible With:Robo R1Robo R1+

Robo R1+ X Carriage Includes: Carriage (1 pcs) Fits: R1/R1+ Note: Does not include the linear bearings. Click here to purchase linear bearings  

Robo R1+ X Carriage with Bearings  This is the bracket the extruder rides on. Includes: Carriage (1 pcs)Bearings (4 pcs) Fits:Robo R1Robo R1+ Note: this latest batch came bulk packaged, so there is minor scuffing on some of the plastic.

Robo R1+ Y Axis Pillow Blocks  Two complete sets. Hardware not included. Includes: Pillow block - top half (2 pcs)Pillow block - bottom half (2 pcs)  Fits:Robo R1Robo R1+ 

Robo R1+ Y Belt Clamp - 2 Pack Includes: Belt clamp (2 pcs) Location: Y belt Fits:Robo R1Robo R1+

Y Bracket for Robo R1+ These brackets connect the two Y-Axis rods that the bed travels on.  Note: Magnets will need to be glued in, in the appropriate orientation for your glass bed. We recommend using Epoxy, Polymer Bonding Kit or...

Idler Side Z Axis Carriage for Robo R1+ Replacement Z Carriage for the idler side Z-axis (non motor side) Includes: Carriage (1 pcs) Location: Idler Side Fits: R1+ Note: This is the carriage only, it does not...

Motor Side Z Carriage for Robo R1+ Replacement z axis carriage with motor mount for Z-axis. Includes: Carriage (1 pcs) Location Motor Side (1 pcs) Fits: R1+ Note This is the carriage only, it does not include: bearings, leadscrew...