SV08

Microswiss Brass Plated Wear Resistant Nozzle for FlowTech™ Hotend FlowTech nozzles are designed to be leak proof and offer an effortless and quick nozzle replacement process. The FlowTech design seamlessly integrates the thermal tube with the...

Bowden Collet with Clip Replacement Collet for our RepRap V6 Heatsinks Suitable for 4mm OD Bowden tube Note: Collet is black, color of clip may vary. Fits: PB Select™ V6 HeatsinkOrbiter Extruder V2.0Sovol SV08Generic V6 heatsinksSovol...

  FlowTech™ - CHT High Flow Nozzles Microswiss and Bondtech have partnered to bring the High Flow nozzle to the FlowTech ecosystem. This new nozzle incorporates proprietary CHT technology, specifically designed to enhance the filament flow...

  FlowTech™ - CM2 CHT High Flow Nozzles Microswiss and Bondtech have partnered to bring the High Flow, Hardened tip CM2™ nozzle to the FlowTech ecosystem. This new nozzle incorporates proprietary CHT technology, specifically...

3D Print Cleanup Tool This deburring tool is great for cleaning the brim off the long, straight edges of your 3D prints. We find it easier to use than an Exacto knife, because the blade doesn't dig into the plastic print as easily. The swivel head makes...

Extruder Adapter Board Kit Includes: Extruder adapter board top (1 pcs)Extruder adapter board bottom (1 pcs)Hardware Kit (1 pcs) Fits: SV08

Extruder Assembly for Sovol SV08 Includes: Extruder assembly (1 pcs) Fits: SV08

Extruder Stepper Motor Includes: Extruder motor with gear (1 pcs) Fits: Sovol ZeroSV08

Main Wire Harness for Extruder Connects from mainboard to extruder. Includes: Wire harness (1 pcs) Fits: SV08

4010 Axial Fan - 24 Volt Includes: Fan (1 pcs) Specifications:Size: 40x40x10mmVoltage: 24vdcRPM: 5500Wires: 2 Fits: SV08

Filament Runout Sensor Includes: Sensor Switch (1 pcs) Fits: Sovol ZeroSV08

Build Plate (Print Surface) Textured PEI powder coated on one side Includes: Build plate (1 pcs) Fits: SV08

  DiamondBack FlowTech™ Nozzles The collaboration between Micro Swiss and DiamondBack introduces the most advanced nozzle to the FlowTech ecosystem. This nozzle features a proprietary Polycrystalline Diamond (PCD) insert, developed after 40...

Microswiss FlowTech™ Hotend for Sovol SV08 This kit comes with a plug-and-play heater core and thermistor, fully compatible with the Sovol SV08 printer. Stock z-height, build volume and firmware remains unchanged. By upgrading your Sovol...

FlowTech™ Silicone Socks A pack of 3 high temperature non-stick silicone socks for FlowTech™ hotend.Socks are made of a heat-resistant, non-stick silicone material, it will keep your heater block clean and will help retain the heat...

Heated Bed Assembly for SV08 Includes: Bed Heater (1 pcs)Magnet - Installed (1 pcs) Fits: SV08

Retaining Clip for Heater Block This clip holds the heater and thermistor in place on the heater block. Includes: Clip (1 pcs) Fits: SV08

Hotend Heater Cartridge Heats the hotend Includes: Heater (1 pcs) Fits: SV08

Hotend Air Duct Set Directs airflow to the part being printed Includes: Front air duct (1 pcs)Rear air duct (1 pcs) Fits: SV08 Note: The front air duct comes in two separate pieces. Carefully snap them together before installation.

Hotend Assembly for SV08 Includes: Heat break (1 pcs)Heater block (1 pcs)Heater cartridge (1 pcs)Thermistor (1 pcs)Silicon sock (1 pcs)M3x15 socket head cap screws (2 pcs)M2.5x30 socket head cap screws (1 pcs)0.40mm nozzle (1 pcs) Fits: SV08