Universal Fit

PB select™ Magnets Includes: 20x6x2mm magnet (10 pcs)

3D Print Removal Tool - Scraper Includes: Scraper (1 pcs) Length: 175mmBlade width: 39mm

PB Select™ Metal Fan Guard Includes: Fan guard (1 pcs) Fits: 40x40mm fans Note: Mounting screws not included

Blinker Board - 3.5 amp Protects tool batteries from over discharge. Includes: Blinker Board (1 pcs) Compatible with: DeWalt, Milwaukee and Makita (12/18/20 volt Lithium Ion batteries.) Max Current: 3.5 amps (This is not [Ah] amp...

MR85ZZ Ball Bearings High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (2 pcs) Specifications:ID: 5mmOD: 8mmW: 2.5mm Note: Does not fit the new BMG IDGA extruders

Belt Tension Spring Includes: Spring (1 pcs) Fits: 9mm melt

*Clearance item, no returns Timing Belt Tensioner Spring Universal belt tensioner spring for 3D printer 6mm drive belts Fits: 6mm Timing GT Belts

Bowden Collet with Clip Replacement Collet for our RepRap V6 Heatsinks Suitable for 4mm OD Bowden tube Note: Collet is black, color of clip may vary. Fits:Flashforge Adventurer 5MFlashforge Adventurer 5M Pro PB Select™ V6 HeatsinkOrbiter...

Bowden Tube Cutter for PTFE Tubing This handy little tool easily makes super clean cuts in PTFE tubing. Buy premium Capricorn PTFE tubing here.  

Bowden Tube Cutter for PTFE Tubing This handy little tool easily makes super clean cuts in PTFE tubing. Buy premium Capricorn PTFE tubing here.    

5 Amp DC-DC Buck Converter XL4015 Input voltage 4.0 ~ 38V Adjustable output voltage range 1.25V ~ 35V (Input voltage must be higher than the output voltage by 1.5V) Output current 4A recommended (up to 5A) Power indicator light Includes...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 1 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 2 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the...

Universal BLTouch Cable - 1 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...

Universal BLTouch Cable - 1.5 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...

Universal BLTouch Cable - 2 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...

Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...

PB Select™ Plated Copper Nozzle High precision copper nozzles is great for printing everything from PLA to PEEK.Copper has a much higher thermal conductivity than brass and these nozzles can handle high temperatures (up to 495c)...

PB Select CopperBlock™ Heater Block Nickel composite coated copper increases thermal conductivity.  Includes: Heater block (1 pcs)Set screw (1 pcs)Clamping screw (1 pcs) Specifications:Plating: Nickel CompositeMax Temperature:...

CopperBlock™ Hot Block This Volcano style heater block is compatible with E3D thermistor cartridges and high temperature, high accuracy PT100 temperature sensors. Includes:  Heater block (1 pcs)Set screw (1 pcs)Clamping screw (2...