Universal Fit

Bondtech Ball Bearing High precision ball bearing used in the Bondtech BMG and dual/single direct extruders for Raise3D. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 8MMW: 2.5mm Note: Not for use with the IDGA extruders.

MR95ZZ  Bearing for Titan and Titan Aero Extruder Includes: Bearing (2 pcs) Specifications:ID: 5mmOD: 9mmW: 3mmMR95ZZABEC 5 Fits: TitanTitan Aero

  Flashforge Bearing (105ZZ) This is the bearing that goes on the inner side of the pulley on the Y axis drive shaft. Includes: Bearing (1 pcs) Specifications:ID: 5mmOD: 10mmW: 4mm Fits:DreamerDreamer NXInventor Note: Sold in units...

Belt Tension Spring Includes: Spring (1 pcs) Fits: 9mm melt

Timing Belt Tensioner Spring Universal belt tensioner spring for 3D printer 6mm drive belts Fits: 6mm Timing GT Belts

Arco Electronics Rocker Switch - Black  Includes: Rocker switch (1 pcs) 10A 250VACMFG Part Number: 8600VB Datasheet

Bondtech BMG Extruder - Right Hand Includes:Extruder (1 pcs)Motor gear (1 pcs) Notes:Does not include stepper motorFor 1.75 mm diameter filament onlyPlease note the orientation of the motor gear in the photoThe extruder can use any Nema17 motor with...

Bondtech BMG-M Extruder for Slice Engineering Mosquito Hotends For 1.75mm filament Optimized for the Slice Engineering Mosquito and Mosquito Magnum hotends High performance and resolution with low weight Bondtech's precise Dual-Drive...

Bowden Collet with Clip Replacement Collet for our RepRap V6 Heatsinks Suitable for 4mm OD Bowden tube Note: Collet is black, color of clip may vary. Fits: PB Select™ V6 HeatsinkOrbiter Extruder V2.0Sovol SV08Generic V6 heatsinksSovol...

Set of 3 Bowden Collets for Microswiss CR10 Hotend kit Includes: Collets (3 pcs)Red collet clips (3 pcs) Fits:Microswiss hotend for CR-10 & Ender KitMicroswiss hotend for CR-10s Pro Kit

Bowden Tube Cutter for PTFE Tubing This handy little tool easily makes super clean cuts in PTFE tubing. Buy premium Capricorn PTFE tubing here.  

Bowden Tube Cutter for PTFE Tubing This handy little tool easily makes super clean cuts in PTFE tubing. Buy premium Capricorn PTFE tubing here.    

5 Amp DC-DC Buck Converter XL4015 Input voltage 4.0 ~ 38V Adjustable output voltage range 1.25V ~ 35V (Input voltage must be higher than the output voltage by 1.5V) Output current 4A recommended (up to 5A) Power indicator light Includes heat sink ...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 1 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the...

Extension Cable, Stepper Motor to Dupont 4 (No Latch). Approximately 2 meter long Nema 17 stepper motor 6-pin connector to Dupont 4-pin connector. The default wiring for this extension cable is listed below. You may need to switch the...

Universal BLTouch Cable - 1 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...

Universal BLTouch Cable - 1.5 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...

Universal BLTouch Cable - 2 Meter This is one long cable that plugs directly into the BLTouch and eliminates the additional joints created when using other BLTouch extension cables. Comes standard with BLTouch connector on one end and a Dupont 3 pin...

  Flashforge Extruder Motor Cable (Stepper Motor Cable) Includes: Cable (1 pcs) Length: 118 cm (1180mm) Plug A: PH 6 PinSide B: XH254 4 Pin Fits: Dreamer NX

Stepper Motor Cable with Latch Length: 1 meter Connectors: 4-pin Dupont w/latch to JST-XH6 6 pin. This is a universal cable. Depending on your setup you may need to relocate the pins in the connector housing Controller Side     Motor...