Parts & Accessories

Prusa MK2.5S/MK3S/+ Mosquito Upgrade Kit This kit is used to upgrade a current Bondtech extruder to use a Mosquito hotend. Includes:1x SLS 3D printed front housing1x SLS 3D printed back housing1x SLS 3D printed Mosquito fan shroud1x SLS 3D printed...

PB Select™ M3 Stainless Steel Square Nuts These thin square nuts work in many applications that require a thinner (1.75mm) square nut. Including E3D Hemera Stepper Motors, Prusa Printers and Bondtech Extruders. Includes: Square Nut (10 pcs)...

M5 Brass Thread Insert - 4 Pack Size: M5 OD: 7.5mm Length: 6mm Recommended hole diameter: 6.75 mm For easy installation use the heat-set insert soldering iron tip by Virtjoule

Bondtech M5x10 low head cap screw for Bondtech Extruders, to be used with the M5 thread inserts or similar. Sold in units of one

Black-coated M5x10 low head cap screw to be used with the M5 thread inserts or similar. Sold as a 5 pack

Bondtech Metal Push Fit Connector  For 4mm Tube Thread G1/8″

Bondtech Motor Gear for BMG Extruder 17 tooth brass gear with M3x3 set screw. Used in Bondtech BMG single and dual direct extruders. Note: Make sure that the set screw does not collide with the secondary plastic gear when assembled.

Needle Bearings for Bondtech BMG - 2 Pack For shaft diameter of 3mm. High precision needle bearing for Bondtech BMG drive gears. Includes: Needle bearing (2 pcs) Specifications:(Measured by hand - sizes are approximate)ID: 3.1mmOD: 4.9mmL: 6.7mm

Bondtech Needle Bearing for Shaft Diameter 3.0 mm  High precision needle bearing that is used in Bondtech drive gears for shaft diameter 3.0 mm. Please Note: Sold in units of 1. Two bearings are used per drive gear, so make sure to order two if...

Nema 17 Geared Stepper Motor for Bondtech Extruders Nema17 geared stepper with 5.18:1 ratio and a planetary gear reducer and a 700 mm long PC2510 cable with quick-fit connectors (see additional cable sizes available in Related Products below) For best...

22mm Nema 17 Stepper Motor for Bondtech Extruder Nema17 Pancake stepper motor with a 41 cm non-detachable, bare end leads (no plug). Max Input current: 0.8A Step angle: 1.8 deg. Torque: 12 Ncm Outputshaft diameter: 5.0 mm with flat. Hole for...

Genuine Bondtech Drive Gear Set for Prusa 3D Printers Comes as a set consisting of a primary drive gear, a secondary gear, bearings and shaft. Includes: Bondtech gear with a grub screw (1 pcs)Bondtech gear without a grub screw (1 pcs)Bearings (2...

PTFE Fittings Set for Prusa Mini Use this set to simplify the install, use and maintenance of Prusa Mini’s bowden tube.Instead of using 3 PTFE tube sections, use one only.Includes push-fit collets for ease of use and effective hold of the...

Bondtech 6mm Collet (Push Fit Collar) for 3mm Filament High quality replacement push-fit collar with metal teeth. Includes: Collet (1 pcs)  Fits: 2.85/3mm filament and 6-6.4 mm PTFE Tube.

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...

Bondtech Brass Push Fit Connector for 4mm tube 4mm assembles in 8mm pocket, with a minimum depth of 5 mm.

Push Fit ECAS - 4mm For use on BondTech extruders that use the ECAS push fit. Sold in units of 1

Bondtech Raise3D Dual Direct Adapter  The kit includes two adapter cables. Older model Raise3D N1/N2 printers with the silver color motors have a stepper motor connection that does not fit the motors on the Dual Direct Extruder, so an adapter...

Bondtech Raise3D Single Direct Adapter This kit includes one adapter cable. Older Raise3D N1/N2 printers with the silver color motor have a stepper motor connection that does not fit the motors on the Single Direct Extruder, so an adapter is...

Bondtech Extruder Rebuild Kit (v1.7) for Wanhao D9 This rebuild kit for Bondtech Wanhao D9 Extruder will make it possible to use the latest revision of the new breakout board that have a wider clip than before. The older existing breakout board was...