Bondtech & Compatible

Bondtech Brass Push Fit Connector for 4mm tube 4mm assembles in 8mm pocket, with a minimum depth of 5 mm.

Push Fit Connector Contains 4 push fit connectors  PC4-01 for 4mm PTFE tube These connectors have a stop point, so the PTFE tube will not pass all the way through. 

Push Fit ECAS - 4mm For use on BondTech extruders that use the ECAS push fit. Sold in units of 1

Bondtech Raise3D Dual Direct Adapter  The kit includes two adapter cables. Older model Raise3D N1/N2 printers with the silver color motors have a stepper motor connection that does not fit the motors on the Dual Direct Extruder, so an adapter...

Bondtech Raise3D Single Direct Adapter This kit includes one adapter cable. Older Raise3D N1/N2 printers with the silver color motor have a stepper motor connection that does not fit the motors on the Single Direct Extruder, so an adapter is...

Bondtech Extruder Rebuild Kit (v1.7) for Wanhao D9 This rebuild kit for Bondtech Wanhao D9 Extruder will make it possible to use the latest revision of the new breakout board that have a wider clip than before. The older existing breakout board was...

M3x2 Set Screw for Bondtech Extruder M3x2 set screw for primary gear with inner diameter of 5mm. Hard 12.9 Grade for durability. Sold in pack of 5    

M3x3 Set Screw Includes: Set screw (5 pcs) 12.9 GradeCup point

M4X3 Set Screw 12.9 Grade Sold in a 4 pack    

M4x3 Set Screw for Bondtech Extruder M4x3 for primary gear with inner diameter of 8mm. 12.9 Grade Sold in units of one  

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x20mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 3.0x32 mm Sold in units of one. 

Stainless steel shaft for Bondtech gear kits.  Size: 4X22mm Sold in units of one. 

4x22mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

Stainless steel shaft for Bondtech gear kits.  Size: 4X25mm Sold in units of one. 

4x25mm hardened and precision ground shaft for Bondtech gear kits.  Sold in units of one

SLS 12mm EZABL Mount For DDX Mount a 12mm EZABL bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance With square nut pockets for increased (re)threading...

SLS 18mm EZABL Mount For DDX Mount a 18mm EZABL bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance With square nut pockets for increased...

  LDO Nema14 Round HT Stepper Motor Includes:NEMA14 1.8° Pancake stepper motor (1 pcs)1 meter integrated lead wire with XH 4 pin connector (1 pcs) Fits:LGX LiteOrbiterHextrudORTSherpa Mini Specs:Max Current: DC 1.0 A / phaseRecommended...

NEMA 17 Slim Power Stepper Motor (0.9 Degree) Nema 17 high resolution 0.9 degree pancake stepper motor. Perfect fit for the BMG / Prusa extruder upgrades or E3D Titan Extruder. Includes:Stepper Motor (1 pcs)1000 mm long cable with Dupont 4-pin...