DDX for Creality

Bearing for DDX Direct Drive Extruder & IDGA Ball bearing to use in Bondtech DDX Direct Drive eXtruder Includes: Bearing (1 pcs) Specifications:ID: 4mmOD: 8mmW: 3mm Fits:DDXIDGA

SLS BLTouch Mount for Microswiss, Creality Pro or Mosquito Hotend (on DDX) Mount a BLTouch bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance The...

SLS BLTouch Mount for Copperhead Hotend (on DDX) Mount a BLTouch bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance The precise height adjustment to...

DDX Adapter For Copperhead™ Screw Mount To use with: Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Copperhead™ hotend with screw mount heat sink on a DDX Upgrade Kit

DDX Adapter For Microswiss All-Metal Use a Microswiss All Metal hotend with the Bondtech DDX. Part is SLS printed in PA12 (Nylon) Requires DDX extruder v2 or later. This part is necessary to install a Microswiss All Metal hotend on a DDX Direct...

DDX Adapter for Mosquito To use with Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Slice Engineering's Mosquito hotend in a DDX Upgrade kit. Important Notes from Bondtech:Upgrading the hotend to...

DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10 S4 CR-10 S5 Requires your printer to have a 40x40x10mm Radial Fan...

DDX Bed Rod Holder Set for Ender-5 Plus Use the whole print surface of the Ender-5 Plus with this accessory Strong Plastic Parts made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance...

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included

DDX v2 Rear Housing For owners of DDX v1 units only This housing allows you to use a Micro Swiss all metal hotend in your DDX V1.SLS made part using Polyamide 12 (Nylon).

DDX v3 Adapter Set For Creality CR-10v2 and Cr10v3 Please Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatible with DDX v3, now even easier to install Fit a Direct Drive eXtruder on...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch bracket needed Creality CR-10 Max * - BLTouch bracket...

DDX v3 Adapter Set For Creality Ender and CR-10 Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatibility Table To use with 40x40x10 fans on: Creality Ender-3 Ender-3 v2 Ender-3 Pro Creality...

  E3D Thermistor Cartridge  Cartridge type Semitec 104NT thermistor suitable for all E3D (and other) hotends using a cartridge type heater block. Includes: Thermistor (1 pcs) Specs:Max temperature: 300°CCartridge diameter:...

SLS 12mm EZABL Mount For DDX Mount a 12mm EZABL bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance With square nut pockets for increased (re)threading...

SLS 18mm EZABL Mount For DDX Mount a 18mm EZABL bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance With square nut pockets for increased...

  Super Lube 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...