Creator Max

Spatula for removing 3D prints from the build surface. his is the same tool that is provided with all new Flashforge 3D printers. 

Flashforge Extruder Air Duct  Directs air to the part being printed Fits: Creator Pro Creator Max Dreamer (not for Dreamer NX) Inventor (not for Inventor 2) Air Duct only, does not include mounting screws

Flashforge V Bearing  Fits: Adventurer 3 Creator 3 Creator Pro/Max Dreamer Dreamer NX Finder 2.0 Guider 2 Guider 2S HT Inventor Inventor 2 Sold in units of 1

Bed Heater Mounting Hardware This hardware set is for mounting the PCB bed heater to the glass build plate on the below listed Flashforge 3D printers. Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor

Flashforge Bed Leveling Bolt - 3 Pack Fits:  Inventor Creator Pro Creator Pro 2 Creator Max Dreamer Note: Bed Leveling Nuts and Bed Leveling Springs not included.  

Flashforge Build Plate Note: Does not include print surface (available here) Fits: Creator Pro Creator Pro 2 Creator Max Inventor Dreamer Dreamer NX

Flashforge Flexible Spring Steel Build Plate System Includes Flashforge print surface pre-installed Magnet sheet with adhesive for easy installation  Spring steel flex print surface Fits: Creator Pro 2 Creator Pro Creator...

Flashforge LED cable Fits: Creator Pro Creator Max

Flashforge Extruder Motor Cable (wiring) For Left Extruder Motor Fits: Creator Max Inventor Dreamer    

Flashforge Extruder Motor Cable (wiring)  For Right Extruder Motor  Fits: Creator Max Inventor Dreamer 2    

Flashforge X Endstop Sensor Cable (X-Max) Length:1100mm Fits: Creator Pro Creator Max

Flashforge Z Min Sensor (Endstop) Cable Fits: Creator Pro Creator Max Dreamer Dreamer NX

Flashforge Extruder Motor Cable For Left Extruder Motor Fits: Creator Max

Flashforge Creator Max X Motor Cable Fits: Creator Max

Hotend Mounting Block

Flashforge Extruder Carriage (Bracket) Does not include bearings. Purchase the correct bearings here. Fits: Creator Pro Creator Max Dreamer Inventor 

Left Side Filament Extruder Lever Assembly for Flashforge Includes: Filament lever Backing plate assembly Grove bearing Grove bearing retaining plate Shoulder bolt Spring 6mm flat head mounting screw Filament drive gear Set...

Right Side Filament Extruder Lever Assembly for Flashforge Includes: Filament lever Backing plate assembly Grove bearing Grove bearing retaining plate Shoulder bolt Spring 6mm flat head mounting screw Filament drive gear set...

Flashforge Extruder Spring Length: 21.5mm Fits: Adventurer 3 Creator 3 Inventor Inventor 2 Finder Creator Pro Creator Pro 2 Creator Max Dreamer Dreamer NX  Also Compatible with: MP Voxel Robo E3  

Flashforge Blower Fan This is the fan that cools the part being printed Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor

Flashforge 40x10mm Fan (Left Side) Fits: Creator Max (Left Side)

Flashforge 40x10mm Fan (Right Side) Fits: Creator Max (Right Side)

Flashforge Filament Drive (Extruder) Gear Hardened steel for longer life when printing abrasive materials such as Carbon Fiber PETG M4x4 Set screw included Fits: Creator 3 Guider 2S HT Guider 2 Inventor Finder Finder 2 Creator Pro Creator...

Flashforge Filament Drive (Extruder) Gear Set screw included Fits: Creator 3 Guider 2S HT Guider 2 Inventor Finder Finder 2 Creator Pro Dreamer Dreamer NX

Flashforge Filament Guide Tube Fits: Creator Max

Flashforge Filament Tension Lever This is the plastic lever only and does not include any hardware Fits: Adventurer 3 Dreamer NX Creator Pro (Right Side) Dreamer (Right Side) Inventor (Right Side) Creator Max (Right Side) Also compatible...

Flashforge Heat Break (Threaded Pipe)  Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor  

Heat Break (Thermal Tube) for Micro Swiss MK10 / MK11 All Metal Hotend Kits This is a replacement heat break for the Micro Swiss MK10/MK11 hotends. The lower thermal break is made from stainless steel, and the colder upper part is made from...

Heated Build Plate Assembly Includes: Glass build plate PCB bed heater Connection cable Print surface Fits: Creator Pro 2 This build plate assembly will only work with the following printers if you purchase this connection cable...

Heat Resistant Insulation  Cut to shape for the Flashforge heater block Please Note: To attach this to the heater block you will need 5mm kapton tape (not included) available here. Fits: Guider 2S Creator Pro Creator...

Heat Resistant Tape Use this tape to secure the cotton insulation to your Flashforge heater block. Width: 5mm Length: 33 meters

Flashforge Limit Switch - Regular Make sure your current switch matches the switch in the picture.  Fits: Creator Pro/Max Dreamer Dreamer NX Inventor 2

THK Linear Bearings for Flashforge 3D Printers High precision THK bearings.  These are the 17mm long linear bearings that the plastic carriage (bracket) rides on.   Fits: Creator Pro Creator Max Dreamer Dreamer...

Flashforge Creator Max Mainboard  

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.20mm Please note: The 0.20mm nozzles have no markings to indicate the size Fites: Flashforge Guider 2 (not high tamp version) Flashforge Inventor Flashforge Inventor 2S FlashForge...

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.40mm Fites: Flashforge Guider 2 (not high tamp version) Flashforge Inventor Flashforge Inventor 2S FlashForge Creator Pro/Max FlashForge Dreamer/NX FlashForge Finder Qidi Tech...

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.60mm Fites: Flashforge Guider 2 (not high tamp version) Flashforge Inventor Flashforge Inventor 2S FlashForge Creator Pro/Max FlashForge Dreamer/NX FlashForge Finder Qidi Tech...

MK10 Brass Nozzle for PTFE Lined Hotend Orifice Size: 0.80mm Fites: Flashforge Guider 2 (not high tamp version) Flashforge Inventor Flashforge Inventor 2S FlashForge Creator Pro/Max FlashForge Dreamer/NX FlashForge Finder Qidi Tech...

MK10 H4 Hardened Steel Nozzle from Performance 3D  Orifice size: 0.40mm For PTFE lined hotends This wear-resistant, high lubricity nozzle is suited for any printer that uses an MK10 nozzle. These nozzles are manufactured using heat-treated A2...

MK10 H6 Hardened Steel Nozzle from Performance 3D  Orifice Size: 0.60mm For 1.75mm diameter filament Sold in units of 1 For PTFE lined MK10 hotends only  This wear-resistant, high lubricity nozzle is suited for any printer that uses an...