Dreamer

Spatula for removing 3D prints from the build surface. his is the same tool that is provided with all new Flashforge 3D printers. 

Flashforge Extruder Air Duct  Directs air to the part being printed Fits: Creator Pro Creator Max Dreamer (not for Dreamer NX) Inventor (not for Inventor 2) Air Duct only, does not include mounting screws

Flashforge V Bearing  Fits: Adventurer 3 Creator 3 Creator Pro/Max Dreamer Dreamer NX Finder 2.0 Guider 2 Guider 2S HT Inventor Inventor 2 Sold in units of 1

Flashforge Flange Bearing This is the bearing that goes on the inner side of the pulley on the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are needed per shaft

Bed Heater Mounting Hardware This hardware set is for mounting the PCB bed heater to the glass build plate on the below listed Flashforge 3D printers. Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor

Flashforge Bed Leveling Bolt - 3 Pack Fits:  Inventor Creator Pro Creator Pro 2 Creator Max Dreamer Note: Bed Leveling Nuts and Bed Leveling Springs not included.  

Flashforge Bed Leveling Thumb Nut - 3 Pack Fits:  Inventor Inventor 2 Finder 2 Creator Pro Dreamer Dreamer NX  

Flashforge Replacement Drive Belt Length: 880mm Fits:  Dreamer Dreamer NX Inventor Sold in units of 1

Flashforge Timing Belt  Size: 250mm Fits:  Creator Pro Dreamer Dreamer NX Finder 2 Inventor Inventor 2  

Flashforge Replacement Drive Belt Length: 590mm Fits: Creator Pro Dreamer Dreamer NX Inventor

Flashforge Build Plate Note: Does not include print surface (available here) Fits: Creator Pro Creator Pro 2 Creator Max Inventor Dreamer Dreamer NX

Flashforge Flexible Spring Steel Build Plate System Includes Flashforge print surface pre-installed Magnet sheet with adhesive for easy installation  Spring steel flex print surface Fits: Creator Pro 2 Creator Pro Creator...

Flashforge PCB Build Plate Heater Fits: Creator Pro Dreamer Dreamer NX Inventor

Flashforge Extruder Motor Cable (wiring) For Left Extruder Motor Fits: Creator Max Inventor Dreamer    

Flashforge Hotend Cable (wiring) Left Hotend to mainboard This does not include the extruder motor cable. The left extruder motor cable is available here Fits: Inventor Dreamer    

Flashforge Extruder Motor Cable (wiring)  For Right Extruder Motor  Fits: Creator Max Inventor Dreamer 2    

Flashforge Hotend Cable (wiring) Right Hotend to mainboard. This does not include the extruder motor cable. The right side extruder motor cable is available here Fits: Inventor Dreamer    

Flashforge Z Min Sensor (Endstop) Cable Fits: Creator Pro Creator Max Dreamer Dreamer NX

Flashforge Heated Bed Cable Fits: Creator Pro Dreamer Dreamer NX

Hotend Mounting Block

Core Board for Original Dreamer Stamped on Board: FlashForge CoreBoard REVH Please Note: The Micro SD card is not included Fits: Original Dreamer

DFlex™ Build Plate - Single sided textured PEI powder coated flexible print surface  The DFlex build plate allows you the option of having two print surfaces on one build plate. Made from heavy gauge flexible steel. Side one is PEI...

Driver Board for Original Dreamer Stamped on Board: FlashForge DriverBoard REVF Fits: Original Dreamer

Flashforge Dual Extruder Assembly  Fits: Dreamer Inventor Please note: This is the extruder assembly only. The wiring harness is not included. Wires can be purchased separately here:  Right Hotend Cable Left Hotend Cable Left...

FlashForge Extruder PCB Board Fits: Dreamer Inventor  

Flashforge Extruder Carriage (Bracket) Does not include bearings. Purchase the correct bearings here. Fits: Creator Pro Creator Max Dreamer Inventor 

Left Side Filament Extruder Lever Assembly for Flashforge Includes: Filament lever Backing plate assembly Grove bearing Grove bearing retaining plate Shoulder bolt Spring 6mm flat head mounting screw Filament drive gear Set...

Right Side Filament Extruder Lever Assembly for Flashforge Includes: Filament lever Backing plate assembly Grove bearing Grove bearing retaining plate Shoulder bolt Spring 6mm flat head mounting screw Filament drive gear set...

Flashforge Extruder Spring Length: 21.5mm Fits: Adventurer 3 Creator 3 Inventor Inventor 2 Finder Creator Pro Creator Pro 2 Creator Max Dreamer Dreamer NX  Also Compatible with: MP Voxel Robo E3  

Flashforge Blower Fan This is the fan that cools the part being printed Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor

Flashforge 40x10mm Fan 24v, 0.08a Fits: Dreamer Dreamer NX Inventor

Flashforge 80X15mm Fan Volts: 24 Watts:  Chamber fan Fits: Dreamer Dreamer NX

Flashforge Filament Drive (Extruder) Gear Hardened steel for longer life when printing abrasive materials such as Carbon Fiber PETG M4x4 Set screw included Fits: Creator 3 Guider 2S HT Guider 2 Inventor Finder Finder 2 Creator Pro Creator...

Flashforge Filament Drive (Extruder) Gear Set screw included Fits: Creator 3 Guider 2S HT Guider 2 Inventor Finder Finder 2 Creator Pro Dreamer Dreamer NX

Flashforge Filament Tension Lever This is the plastic lever only and does not include any hardware Fits: Adventurer 3 Dreamer NX Creator Pro (Right Side) Dreamer (Right Side) Inventor (Right Side) Creator Max (Right Side) Also compatible...

Flashforge Flange Bearing This is the bearing that goes on the end of the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are needed per shaft

Front Door for Flashforge Dreamer and Inventor Acrylic Comes with 2 magnets pre-installed Fits: Dreamer Dreamer NX Inventor (will not fit Inventor 2)

Flashforge Heat Break (Threaded Pipe)  Fits: Creator Pro Creator Max Dreamer Dreamer NX Inventor  

Heat Break (Thermal Tube) for Micro Swiss MK10 / MK11 All Metal Hotend Kits This is a replacement heat break for the Micro Swiss MK10/MK11 hotends. The lower thermal break is made from stainless steel, and the colder upper part is made from...

Heated Build Plate Assembly Includes: Glass build plate PCB bed heater Connection cable Print surface Fits: Creator Pro 2 This build plate assembly will only work with the following printers if you purchase this connection cable...