M2

Super Lube® 21030 - Synthetic Grease with SYNCOLON™ (PTFE)  This is a Prusa Research approved lubricant.   Can be used on drive gears, Linear bearings or anywhere else you need a high quality grease. Includes: 1...

Molex Terminal Block Plug 5.08mm 2 position 15 ampWire Entry: Right Angle Includes: Plug (1 pcs)

OEM Replacement Touch Screen for MakerGear M3 3D Printers - Cable Not Included Note: This a replacement screen only. These are flashed with the proper firmware. However, your MakerGear printer must already be setup for a touch screen and have the...

  Heater Block for MakerGear V4 Hotend Includes:Heater Block (1 pcs)Set Screws (2 pcs) Fits:M2 (with V4 hotend)M3-SEM3-ID

  Heater Cartridge for MakerGear V4 Hotend  Includes: Heater (1 pcs) Voltage: 24 VDCFor: V4 hotend onlyRated: Up to 300ºC Fits:M2 (with V4 hotend)M3-SEM3-ID Note: If your hotend is able to heat up, but your temperature readings...

  V4 Hot End Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1 pcs)Rubber-coated fiberglass insulation (1 pcs)Nozzle -...

V4 Hotend Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1 pcs)Rubber-coated fiberglass insulation (1 pcs)Nozzle - Stainless...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in tolerances...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in tolerances...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in tolerances...

No returns on this itemAs you install a new nozzle onto a MakerGear hotend, a small amount of material is removed from the nozzle to create a custom fit. This makes the nozzle incompatible with any other barrel due to the slight variations in tolerances...

  Thermistor for MakerGear Printers This thermistor (temperature sensor) is suitable for both the V3b and the V4 Hot Ends.Each thermistor includes the proper Molex connector and can accurately read temperatures up to 300 °C. Includes:...

X-axis belt for MakerGear M3 (Rev.0 Only) and M2 3D Printer Genuine Gates GT Belt Includes: Belt (1 pcs) Location: X-Axis Fits: M3-SE (Rev.0 Only) - If you have an M3-SE Rev.1 click here for the proper beltM2 Note: If your belts...

Timing Belt for MakerGear M2 & M3 3D Printer Genuine Gates GT Belt Includes: Belt (1 pcs) Location: Y-Axis (Bed) Length: 702mm Fits: M3-IDM3-SEM2 Note: If your belts are worn, check your printer for alignment issues—misalignment...