M3

  4010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against incorrect plug-in. All fans should be kept free of...

  4015 Bed Fan This is the fan the cools the part being printed. It is sometimes called the print or part cooling fan.  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 40x40x15mm Fits: M3    

Aluminum Motor Mount This is the extruder motor mount that comes standard on the M3-ID and M3-SE Rev.1 machines Includes: Motor mount (1 pcs)M3x22 bolts (3 pcs) Fits:M3-SEM3-ID

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available separately here

MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3 

  Extruder Stepper Motor for MakerGear 3D printers Includes:1.8° stepper motor basePinion gear (installed) Fits:M2M3 Note: Does not include the 5.16:1 planetary gearbox.

  Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries- Expandable and rubber-coated- Suitable for both the V4...

MakerGear Filament Drive Gear Replacement This gear drives the filament through the extruder. Fits: M2M3-SEM3-ID

  Idler Pulley Set for MakerGear 3D Printers Includes:Bolt (1 pcs)Toothed Pulley (1 pcs)Nylon Bushing (1 pcs)  Note: You need one pulley for each belt. Order 2 sets if you need a pulley for each belt. Fits:M3-SEM3-IDM2 Rev G-H 

  MakerGear X Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M3

  MakerGear Y Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M3

MakerGear Z Axis Limit Switch Includes: Limit switch (1 pcs) Fits:M2M3

  Pinion Gear for MakerGear 3D Printers Goes on the extruder stepper motor shaft inside the gearbox. Fits:M2M3 SEM3 ID Use Loctite 609 to attach to motor shaft. Buy Loctite 609 here

X/Y Stepper Motor for MakerGear 3D printers These motors are used to drive both the X and Y motion. Order 2 motors if you need to replace both axis.  Includes: Motor (1 pcs) Specs: 1.8° stepper motor with shaftx16 microstepping88...

MakerGear Z Stepper Motor with Leadscrew and Nut Includes: Z motor with integrated leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits:M3 SEM3 IDM2 RevG or later (with black z motor) Note: The leadscrew nut on this latest batch is white, not black...

  MakerGear V4 Hot End Barrel (Heat Break)  Includes: Heat break (1 pcs) Fits: M2 (with V4 hotend)M3-SEM3-ID Installation Instructions Note: A new nozzle is recommend when installing a new barrel. Once a new nozzle has...

  Heater Block for MakerGear V4 Hotend Includes:Heater Block (1 pcs)Set Screws (2 pcs) Fits:M2 (with V4 hotend)M3-SEM3-ID

  Heater Cartridge for MakerGear V4 Hotend  Includes: Heater (1 pcs) Voltage: 24 VDCFor: V4 hotend onlyRated: Up to 300ºC Fits:M2 (with V4 hotend)M3-SEM3-ID Note: If your hotend is able to heat up, but your temperature readings...

  V4 Hot End Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1 pcs)Rubber-coated fiberglass insulation (1 pcs)Nozzle -...

V4 Hotend Assembly for MakerGear 3D Printers Ships fully-assembled, ready-to-install. Includes: V4 heater cartridge (1 pcs)Heat break (1 pcs)Thermistor (1 pcs)V4 heater block (1 pcs)Rubber-coated fiberglass insulation (1 pcs)Nozzle - Stainless...