MK3S

PB Select™ 3mm Nylon Filament  This 3mm nylon filament is used in the wiring harness of Prusa i3 printers.The length is 50cm which is the proper length for the extruder wiring harness. It can be cut down to 30cm if you need it...

PB Select™ Heatbed to Einsy power cable for Prusa (screw-attached type) Runs from mainboard to heated bed.  Includes: Cable (1 pcs) Fits:MK3MK3SMK3S+ Note: Attachment screws not included To replace this part, please consult...

PB Select™ PSU to Einsy Power Cable We use premium pure copper wire, tin plated copper connectors and adhesive heat shrink for a good quality long lasting cable. Includes: Power cable (1 pcs) Specs:Wire: 16 AWGLength: 18 inches...

PB Select™ Plated Copper Nozzle High precision copper nozzles is great for printing everything from PLA to PEEK.Copper has a much higher thermal conductivity than brass and these nozzles can handle high temperatures (up to 495c)...

PB Select CopperBlock™ Heater Block Nickel composite coated copper increases thermal conductivity.  Includes: Heater block (1 pcs)Set screw (1 pcs)Clamping screw (1 pcs) Specifications:Plating: Nickel CompositeMax Temperature:...

PB Select™ Idler Springs for Prusa Extruder Latch & MMU2S/3 Includes: Idler spring (2 pcs) Fits:MK2.5MK2.5SMK3MK3SMK3S+MiniMini+MMU2SMMU3 To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow...

PB Select™ Prusa Specific Titanium Heat Break High grade titanium helps eliminate heat-creep and is lighter than stainless steel. Similar to a standard E3D V6 heat break but with a special internal geometry for use with the...

PB Select™ All Metal Heat Break Includes: Heat break (1 pcs) For 1.75mm filament only Fits:E3D V6 hotendE3D Volcano hotendRepRap hotendPrusa MK2/3 (all variants without MMU)INTAMSYS FUNMATE HT

PB Select™ Titanium Alloy Heat Break for RepRap and E3D V7 Style Hotend Includes: Heat break (1 pcs) Low thermal conductivityHelps eliminate heat creepTitanium creates a sharper thermal cutoff for a more consistent extrusion Extremely smooth...

PB Select™ Idler Pulley Includes: Idler pulley (1 pcs) Fits:MK2MK2SMK2.5MK2.5SMK3MK3SMK3S+MINIMINI+ To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow the manual for your printer model.

PB Select™ Kapton & Aluminum Tape Used to attach the thermistor to the heated bed on Prusa and other 3D printers. Includes:Kapton Tape - adhesive backed, approximately 4x4 inches (1 pcs)Aluminum Tape...

PB Select™ M3 Stainless Steel Square Nuts These thin square nuts work in many applications that require a thinner (1.75mm) square nut. Including E3D Hemera Stepper Motors, Prusa Printers and Bondtech Extruders. Includes: Square Nut (10 pcs)...

M3 Leaf Spring T-Slot Nut (3030) Plated roll-in t-slot nut with leaf spring. Includes: M3 T-Slot nut with leaf spring (5 pcs) Size:(Measured by hand - sizes are approximate)Length: 19.5mmWidth: 12mmHeight: 6.5mm Fits:3030 extrusionPrusa...

PB Select™ Brass Nozzle This premium brass nozzle will provide a smooth consistent print. Includes: Nozzle of selected size (1 pcs) For: 1.75mm diameter filament Fits:Prusa MK2Prusa MK2SPrusa MK2.5Prusa MK2.5SPrusa MK3Prusa...

PB Select™ Heated Bed Assembly - 24 volt Notes:1. NOT compatible with the MK2/2.5 or MINI.2. This is a Prusa compatible bed. If you want the Original Prusa bed, please click here.3. Flexible spring steel sheet NOT...

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

PB Select™ Preset Torque Wrench  Includes:Preset Torque wrench (1 pcs)Bit holder FDM printed in POP Green ASA (1 pcs)1/4 inch socket adapter (1 pcs)6mm socket (1 pcs)7mm socket (1 pcs)8mm socket (1 pcs) Notes:Use on a clean...

Nozzle Wrench Handy little wrench for removing nozzles. Includes: Wrench (1 pcs) Sizes: 7.0 mm (RepRap, E3D, Nextruder Etc)5.5 mm5.0 mm4.5 mm (Sidewinder X3/X4) Fits:E3D V6 NozzlesPrusa Nextruder standard and highflow nozzles7mm RepRap...

PEI Print Surface - 260x242mm Includes: PEI sheet with 3M adhesive backing (1 pcs) Notes:1. This is NOT the Prusa spring steel sheet with smooth double-sided PEI (Link).2. Tiny dots may appear on the PEI surface. These can slightly...

PB Select™ Prusa Compatible V2 P.I.N.D.A Probe Includes: V2 PINDA (1 pcs) Fits:MK2.5MK2.5SMK3MK3S To test your current PINDA probe, follow this guide from the Prusa Knowledge Base.