Parts Finder

DDX Adapter For Micro Swiss All-Metal Use a Micro Swiss All Metal hotend with the Bondtech DDX. Part is SLS printed in PA12 (Nylon) Requires DDX extruder v2 or later. This part is necessary to install a Micro Swiss All Metal hotend on a DDX Direct...

DDX Adapter for Mosquito To use with Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Slice Engineering's Mosquito hotend in a DDX Upgrade kit. Important Notes from Bondtech:Upgrading the hotend to...

DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10 S4 CR-10 S5 Requires your printer to have a 40x40x10mm Radial Fan...

DDX Bed Rod Holder Set for Ender-5 Plus Use the whole print surface of the Ender-5 Plus with this accessory Strong Plastic Parts made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance...

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included

DDX v2 Rear Housing For owners of DDX v1 units only This housing allows you to use a Micro Swiss all metal hotend in your DDX V1.SLS made part using Polyamide 12 (Nylon).

DDX v3 Adapter Set For Creality CR-10v2 and Cr10v3 Please Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatible with DDX v3, now even easier to install Fit a Direct Drive eXtruder on...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch bracket needed Creality CR-10 Max * - BLTouch bracket...

DDX v3 Adapter Set For Creality Ender and CR-10 Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatibility Table To use with 40x40x10 fans on: Creality Ender-3 Ender-3 v2 Ender-3 Pro Creality...

  Micro Swiss Lightweight Direct Drive Extruder with All Metal Hotend Scroll to the bottom of this page for setup instructions.   Important Note There has been an extruder stepper motor update on Creality machines. Before...

  Micro Swiss Lightweight Direct Drive Extruder (Extruder Only Version) This is the "extruder only" version and does not include a hotend. The Micro Swiss All Metal Hotend is available for purchase here  Important Note There has been...

  Micro Swiss Lightweight Direct Drive Extruder with All Metal Hotend This version includes a Micro Swiss All Metal Hotend. The "Extruder Only" version is available for purchase here.  Important Note There has been an...

Dock Pin for Prusa XL Includes: Pin (1 pcs) Fits: Prusa XL To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow the manual for your printer model.

  Door for Build Plate Ribbon Cable Access This is the small plastic door that goes on the bottom of the build plate where the ribbon cable is located.   Includes: Door (1pcs) Fits: Adventurer 4

  Flashforge Door Detection Board Senses when door is closed Includes: Detection board (1 pcs) Fits:Creator 3Inventor 2

  Door Sensor Switch Includes: Door sensor (1 pcs) Fits: Creator 4

Doorstop for Robo R2 Includes: Door stop (1 pcs)Magnets  (2 pcs) Fits: Robo R2

Artillery Dowel Pin (Cylindrical Shaft) Includes: 3x8mm Pin (1 pcs)  Fits: Sidewinder X1Sidewinder X2GeniusGenius ProHornet

Replacement Downtown Board for Robo R2 and C2 3D printers Includes:Downtown board (1 pcs)Screws (3 pcs) Fits:Robo R2Robo C2 Additional mounting screws sold here

Downtown Board Screw Set For mounting the Downtown board. Includes: Screws (3 pcs)  Fits:Robo R2Robo C2