Parts Finder

Please see our return policy regarding electronic items Control board for Prusa MMU2S Replacement control board. This has the MMU2S firmware pre-installed. Includes: Control board with MMU2S firmware (1 pcs) Fits: MMU2S To replace...

PB Select™ Copper Heat Break Copper and stainless steel Includes: Heat Break (1 pcs) Fits:CR-7CR-8SCR-9SCR-10miniCR-10CR-10SCR-10 V2CR-10 V3CR-10 S4CR-10 S5CR-100CR-100BCR20CR20...

PB Select™ Plated Copper Nozzle High precision copper nozzles is great for printing everything from PLA to PEEK.Copper has a much higher thermal conductivity than brass and these nozzles can handle high temperatures (up to 495c)...

PB Select CopperBlock™ Heater Block Nickel composite coated copper increases thermal conductivity.  Includes: Heater block (1 pcs)Set screw (1 pcs)Clamping screw (1 pcs) Specifications:Plating: Nickel CompositeMax Temperature:...

CopperBlock™ Hot Block This Volcano style heater block is compatible with E3D thermistor cartridges and high temperature, high accuracy PT100 temperature sensors. Includes:  Heater block (1 pcs)Set screw (1 pcs)Clamping screw (2...

CopperBlock™ MK8 Hot Block Nickel composite coated copper hot block for increased thermal conductivity. Allows for the use of a bead or 3mm cartridge style thermistor and is great for high temperature printing, up to 485c. Includes:Heater block...

CopperBlock™ Hot Block for Prusa MINI Nickel composite coated copper hot block for increased thermal conductivity.  Includes:Copper heater block (1 pcs)Set screw (1 pcs)Heater clamping screw (1 pcs) Fits:Prusa MINIPrusa MINI+ Note: After...

Slice Engineering Copperhead Heat Break for Prusa MINI/MINI+ The Copperhead Prusa MINI heat break is bimetallic, made of a copper outer body and an interior steel needle, which gives this heat break better cooling performance, allowing for a...

CopperTop™ Heat Break for Artillery - All metal design for higher temperature printing. - Copper cold side (top) for better heat dissipation to the heatsink- Titanium throat has low thermal conductivity to reduce heat creep...

  Please read our returns policy regarding electronic items  Used Item  Board has 41 hours on it.  Core Board for Dreamer NX This is for the older style Dreamer NX that uses both a core board and a driver board. Check your...

DDX Adapter For Copperhead™ Screw Mount To use with: Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Copperhead™ hotend with screw mount heat sink on a DDX Upgrade Kit

DDX Adapter For Micro Swiss All-Metal Use a Micro Swiss All Metal hotend with the Bondtech DDX. Part is SLS printed in PA12 (Nylon) Requires DDX extruder v2 or later. This part is necessary to install a Micro Swiss All Metal hotend on a DDX Direct...

DDX Adapter for Mosquito To use with Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Slice Engineering's Mosquito hotend in a DDX Upgrade kit. Important Notes from Bondtech:Upgrading the hotend to...

DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10 S4 CR-10 S5 Requires your printer to have a 40x40x10mm Radial Fan...

DDX Bed Rod Holder Set for Ender-5 Plus Use the whole print surface of the Ender-5 Plus with this accessory Strong Plastic Parts made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance...

DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included

DDX v2 Rear Housing For owners of DDX v1 units only This housing allows you to use a Micro Swiss all metal hotend in your DDX V1.SLS made part using Polyamide 12 (Nylon).

DDX v3 Adapter Set For Creality CR-10v2 and Cr10v3 Please Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatible with DDX v3, now even easier to install Fit a Direct Drive eXtruder on...

DDX v3 Adapter Set for Creality CR-10S Pro/Max This set is necessary to install a DDX Upgrade Kit on the models listed below. Creality CR-10S Pro Creality CR-10S Pro V2 * - BLTouch bracket needed Creality CR-10 Max * - BLTouch bracket...

DDX v3 Adapter Set For Creality Ender and CR-10 Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatibility Table To use with 40x40x10 fans on: Creality Ender-3 Ender-3 v2 Ender-3 Pro Creality...