Revo

Revo™ High Flow ObXidian Nozzle The Revo High Flow ObXidian combines the Obxidian and High Flow features into one nozzle. Includes: Revo nozzle of selected size (1 pcs) High Flow Features: The Revo High Flow nozzle increases...

E3D Collet Clip Only fits this collet for 4 mm PTFE Tube. Includes: Collet clip (2 pcs) FitsE3D V6E3D Revo SixE3D Revo MiniE3D CRPrusa Bondtech

  Revo Extension Cable Set Includes:Heater cable (1 pcs)Thermistor cable (1 pcs) Length: 1 meter Fits: E3D Revo HeaterCore Notes: These are the standard length cables. Below are links for other lengths.Cables for Revo Six Prusa...

24 Volt Fan for Revo™ Six Includes: 24 volt fan (1 pcs)Clear fan mount (1 pcs) Voltage: 24 voltsSize: 30x10mm

  E3D Dual Ball Bearing Fan - 30mm 12v These fans have the E3D seal of approval. Use for E3D HotEnds, Extruders or anywhere else you need a good quality ball bearing fan. Include: Fan (1 pcs) Specs:Size: 30x30x10mmVoltage: 12 VDCAmps: 0.10Wire...

E3D Hotend Fan - Ball Bearing - 30mm 24v These fans have the E3D seal of approval. Use for E3D HotEnds, Extruders or anywhere else you need a good quality ball bearing fan. Includes: Fan (1 pcs) Size: 30x30x10mmVoltage: 24 VDCLeads: 1mConnector: 2...

Fan Duct for Revo™ Micro Includes: Fan duct (1 pcs) Fits: Revo Micro heatsink 

5 Volt Fan for Revo™ Micro Includes:  Fan (1 pcs) Voltage: 5 voltsSize: 20x20x10mm  Warning  This fan must be connected using the 5V regulator unless connecting directly to a 5V pin.

  Heater Extension Cable Length: 1 meter Fits: E3D Revo HeaterCore

Revo™ HeaterCore for Creality Sprite - 24 volt This is a special Revo HeaterCore intended for use with the Revo Sprite. It uses a 40W heater and a 100K NTC thermistor, which has the same response as a stock Creality thermistor, saving...

High Temperature Heater Block for Revo Hotend This plated copper HeaterBlock allows you to reach up to 500°C with your Revo system (providing you use a PT100 or PT1000), unlocking the possibilities of printing...

Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block. Includes:...

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...

Fan Regulator for Revo™ Micro Drops voltage to 5 volts. For use with E3D Micro Revo Fan. Includes: Regulator (1 pcs) Max Input: 24 volts

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...

Revo™ CR HeaterCore for Creality - 24 volt This is a special Revo HeaterCore intended for use with the Revo CR. It uses a 40W heater and a 100K NTC thermistor, which has the same response as a stock Creality thermistor, saving you the...

Revo Adapter for Creality Sprite Extruder | E3D A replacement Revo adapter for Creality Sprite/Sprite Pro Extruders.  Includes: Adapter (1pcs) Fits:Sprite Sprite Pro 

Revo™ HeaterCore Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring best practices page from E3D...

Revo™ Hemera Upgrade Kit (with fully loaded nozzle kit) Voltage: 12 volt  Nozzle Size: 0.25, 0.40, 0.60, 0.80 (1 each)  This kit includes a Hemera heatsink with a revised design that’s compatible with a Revo...