Sovol

Build Plate (Print Surface) with Magnet Textured PEI powder coated Includes: Build plate (1 pcs)Magnetic base (1 pcs) Size: 310x320mm  Fits: SV06 PlusSV04

Flexible Steel Build Plate - Textured Powder Coated PEI Includes: Build plate (1 pcs)Magnetic base (1 pcs) Size: 235x235mm  Fits: SV06SV05

Build Plate (Print Surface) with Magnet Textured PEI powder coated on one side Includes: Build plate (1 pcs)Magnetic base with adhesive backing (1 pcs) Size: 310x320mm  Fits: SV07 Plus

Build Plate (Print Surface) with Magnet Textured PEI powder coated on one side Includes: Build plate (1 pcs)Magnetic base with adhesive backing(1 pcs) Size: 235x235mm  Fits: SV07

  DiamondBack FlowTech™ Nozzles The collaboration between Micro Swiss and DiamondBack introduces the most advanced nozzle to the FlowTech ecosystem. This nozzle features a proprietary Polycrystalline Diamond (PCD) insert, developed after 40...

Microswiss FlowTech™ Hotend for Sovol SV08 This kit comes with a plug-and-play heater core and thermistor, fully compatible with the Sovol SV08 printer. Stock z-height, build volume and firmware remains unchanged. By upgrading your Sovol...

FlowTech™ Silicone Socks A pack of 3 high temperature non-stick silicone socks for FlowTech™ hotend.Socks are made of a heat-resistant, non-stick silicone material, it will keep your heater block clean and will help retain the heat...

Flush Cut Trimmers Also called side cutters. We use these trimmers for cutting filament, removing supports and cleaning up prints.  Includes: Trimmers (1 pc)

PB Select™ GT2 Stepper Motor Drive Pulley Recommended for use with Gates GT2/3 or other GT belts Includes: Idler pulley (1 pcs)Set screw (2 pcs) Fits: 6mm BeltTeeth: 20Width: 7mmBore: 5mmOuter diameter:15mm

Hardened Steel High Flow Nozzle Made of hardened steel for printing abrasive filaments.  Includes: Nozzle (1 pcs) Size: Select Above For: 1.75mm diameter filament Fits: SV06 PlusSV07SV07 Plus

Bi-Metal Heat Break Includes: Heat break (1 pcs) Fits:SV06SV06 Plus

Heated Bed Assembly for SV08 Includes: Bed Heater (1 pcs)Magnet - Installed (1 pcs) Fits: SV08

Build Plate Heater for SV07 Plus Includes: Aluminum bed heater (1 pcs)Magnetic sheet - installed on bed heater (1 pcs) Fits: SV07 Plus Note: Does not include build plate/print surface or mounting hardware.

Heater Block (Hot Block) Includes: Heater block (1 pcs) Fits: SV06 PlusSV07SV07 Plus Note: Does not include any installation hardware.

Heater Block (Hot Block) Includes: Heater block (1 pcs) Fits: SV06 Note: Does not include any installation hardware.

Retaining Clip for Heater Block This clip holds the heater and thermistor in place on the heater block. Includes: Clip (1 pcs) Fits: SV08

Hotend Heater Cartridge Heats the hotend Includes: Heater (1 pcs) Fits:SV06SV06 PlusSV07SV07 Plus

Hotend Heater Cartridge Heats the hotend Includes: Heater (1 pcs) Fits: SV08

Hotend Air Duct Set Directs airflow to the part being printed Includes: Front air duct (1 pcs)Rear air duct (1 pcs) Fits: SV08 Note: The front air duct comes in two separate pieces. Carefully snap them together before installation.

Hotend Assembly for SV06 Plus, SV07/Plus Includes: Heat break (1 pcs)Heater block (1 pcs)Heater cartridge (1 pcs)Thermistor (1 pcs)Silicon sock (1 pcs)M2.5x10 socket head cap screws (2 pcs)0.40mm nozzle (1 pcs) Fits: SV06 PlusSV07SV07 Plus