Bondtech Extruder Upgrades

Bondtech Extruder Upgrades

Bondtech Logo

  • Copperhead BLTouch Mount for DDX

    BLTouch Mount for Copperhead Hotend on Creality DDX | Bondtech

    Bondtech

    $11.95
    SLS BLTouch Mount for Copperhead Hotend (on DDX) Mount a BLTouch bed leveling sensor onto the DDX Made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature resistance The precise height adjustment...
    $11.95
  • DDS Main Cable Assembly

    DDS Main Cable Assembly - Gen 2 DDS | Bondtech

    Bondtech

    $39.95
    DDS Main Cable Assembly Fits: 2nd Generation DDS for CR-10S Length: 120 cm Includes 1x DDS main cable with: Molex micro-fit male plugs for Heater and Thermistor cartridges JST contact plugs, male, for axial and radial fans...
    $39.95
  • Copperhead adapter for Bondtech DDX

    DDX Adapter For Copperhead Screw Mount | Bondtech

    Bondtech

    $9.00
    DDX Adapter For Copperhead™ Screw Mount To use with: Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Copperhead™ hotend with screw mount heat sink on a DDX Upgrade Kit
    $9.00
  • Micro Swiss Mount for Bondtech DDX

    DDX Adapter For Micro Swiss All-Metal Hotend | Bondtech

    Bondtech

    $9.95
    DDX Adapter For Micro Swiss All-Metal Use a Micro Swiss All Metal hotend with the Bondtech DDX. Part is SLS printed in PA12 (Nylon) Requires DDX extruder v2 or later. This part is necessary to install a Micro Swiss All Metal hotend on a DDX...
    $9.95
  • Bondtech DDX adapter for Mosquito Hotend

    DDX Adapter For Mosquito | Bondtech

    Bondtech

    $9.00
    DDX Adapter for Mosquito To use with Bondtech DDX Direct Drive eXtruder for Creality This set is necessary to install a Slice Engineering's Mosquito hotend in a DDX Upgrade kit. Important Notes from Bondtech:Upgrading the hotend to...
    $9.00
  • DDX Adapter Set For Creality Ender-3 / CR-10

    DDX Adapter Set For Creality Ender-3 / CR-10 | Bondtech

    Bondtech

    $49.95
    DDX Adapter Set For Creality Ender-3 / CR-10 Note: Does not fit DDX V3 This set is necessary to install a DDX Upgrade Kit on the models listed below. Fits: Ender-3 CR-10 CR-10S CR-10 S4 CR-10 S5 Requires your printer to have a 40x40x10mm...
    $49.95
  • Ender 5 bed rod holder set - Bondtech

    DDX Bed Rod Holder Set for Ender-5 Plus | Bondtech

    Bondtech

    $29.95
    DDX Bed Rod Holder Set for Ender-5 Plus Use the whole print surface of the Ender-5 Plus with this accessory Strong Plastic Parts made of PA12 (Nylon) with the SLS 3D printing process Better surface finishing and higher working temperature...
    $29.95
  • Mosquito Thermistor Adapter

    DDX Thermistor Adapter - 3.0mm | Bondtech

    Bondtech

    $3.99
    DDX Thermistor Adapter 3.0mm Use this adapter set to fit the Creality original thermistor into Slice Engineering's Copperhead™ or Mosquito™ Hot Block Please Note: Thermistor and hot block shown in picture are NOT included
    $3.99
  • DDX v3 Adapter Set For Creality CR-10 V2 and CR-10 V3

    DDX v3 Adapter Set for CR-10 v2 & CR-10 v3 | Bondtech

    Bondtech

    $68.95
    DDX v3 Adapter Set For Creality CR-10v2 and Cr10v3 Please Note: Only fits DDX v3 This set is necessary to install a DDX v3 upgrade kit on the models listed below. Compatible with DDX v3, now even easier to install Fit a Direct Drive eXtruder on...
    $68.95