M2

  4010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 40x40x10mmLocation: Extruder or electronics case Fits: M2 (12 volt version) This is the smaller of the two fans mounted in front...

  4010 Extruder Fan This is the smaller of the two fans mounted in front of the extruder and also used inside the electronics case. This fan has a keyed connector, guarding against incorrect plug-in. All fans should be kept free of...

  5010 Extruder Fan for MakerGear M2 - 12 volt  Includes: Fan (1 pcs) Voltage: 12 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (12 volt version) Mounted at a 45 degree angle in front of the extruder's 40mm fan, this...

  5010 Extruder Fan for MakerGear M2 Dual Extruder - 24 volt  Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 Dual Extruder  This fan has longer leads to accommodate the M2 Dual 3D...

  5010 Extruder Fan for MakerGear M2 - 24 volt Includes: Fan (1 pcs) Voltage: 24 VDCSize: 50x50x10mmLocation: Extruder Fits: M2 (24 volt version) Mounted at a 45 degree angle in front of the extruder's 40mm fan, this 50 mm...

  Silicone Bed Heater for MakerGear M3 & M2 - 24 Volt  Includes: Bed heater (1 pcs) Fits:M2 (24 volt version only)M3-SEM3-ID Note: Terminal block plug not included. Available separately here

  Bed Spring - M2 older version bed - 3 Pack Includes: Spring (3 pcs) Fits: MakerGear M2 (that have a 3 point bed with springs).

MakerGear Bed Thermistor Includes: Thermistor (1 pcs) Fits: MakerGear M2MakerGear M3 

  Extruder Stepper Motor for MakerGear 3D printers Includes:1.8° stepper motor basePinion gear (installed) Fits:M2M3 Note: Does not include the 5.16:1 planetary gearbox.

  Fiberglass Insulation for MakerGear Hot Ends Includes: Insulation (1 pcs) Fits:M2M3-SEM3--ID - Insulation maintains your hot end's temperature and prevents potential burn injuries- Expandable and rubber-coated- Suitable for both the V4...

MakerGear Filament Drive Gear Replacement This gear drives the filament through the extruder. Fits: M2M3-SEM3-ID

  Idler Pulley Set for MakerGear 3D Printers Includes:Bolt (1 pcs)Toothed Pulley (1 pcs)Nylon Bushing (1 pcs)  Note: You need one pulley for each belt. Order 2 sets if you need a pulley for each belt. Fits:M3-SEM3-IDM2 Rev G-H 

  Idler Set for MakerGear M2 3D Printers Includes:Bolt (1 pcs)Bearings (3 pcs)E-clip (1 pcs) Fits: M2 Rev A through F Note: for the MakerGear M2 Rev G through H, use the M3 idler set available here

MakerGear X Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M2

  MakerGear Y Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M3

MakerGear Z Axis Limit Switch Includes: Limit switch (1 pcs) Fits:M2M3

  Pinion Gear for MakerGear 3D Printers Goes on the extruder stepper motor shaft inside the gearbox. Fits:M2M3 SEM3 ID Use Loctite 609 to attach to motor shaft. Buy Loctite 609 here

  SD Card Reader Includes: Card reader (1 pcs) Fits: MakerGear M2

X/Y Stepper Motor for MakerGear 3D printers These motors are used to drive both the X and Y motion. Order 2 motors if you need to replace both axis.  Includes: Motor (1 pcs) Specs: 1.8° stepper motor with shaftx16 microstepping88...

MakerGear Z Stepper Motor with Leadscrew and Nut Includes: Z motor with integrated leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits:M3 SEM3 IDM2 RevG or later (with black z motor) Note: The leadscrew nut on this latest batch is white, not black...