M2

  Idler Set for MakerGear M2 3D Printers Includes:Bolt (1 pcs)Bearings (3 pcs)E-clip (1 pcs) Fits: M2 Rev A through F Note: for the MakerGear M2 Rev G through H, use the M3 idler set available here

MakerGear X Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M2

  MakerGear Y Axis Limit Switch Includes: Limit switch (1 pcs) Fits: M3

MakerGear Z Axis Limit Switch Includes: Limit switch (1 pcs) Fits:M2M3

Henkel 60905 LOCTITE® 609™ Press Fit Retaining Compound - .5 mL (.02 oz) Capsule This is what MakerGear recommends for installing the pinion gear onto the extruder motor shaft of the M2/M3 3D Printers MSDS

Replacement Magnet sheet for 203*254mm FlexSys™ Build Plate Includes: Sheet magnet with adhesive backing (1 pcs) Size: 203x254mmMax temperature: 90c Fits:MakerGear M2MakerGear M3  

Molex Connector Set for MakerGear 3D Printers This connector is used for the MakerGear thermistor and heater cartridge. Each set includes:1x Molex connector receptacle, 2 position, 3mm1x Molex connector plug, 2 position, 3mm2x...

PB Select Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block...

Original BuildTak Sheet Size: 203x254mm (8x10in) Includes: Original BuildTak Sheet (1 pcs) Features:Creates an optimal bond between the 3D printed object and build surfaceAllows for clean and easy removal of the object from the build...

PB Select™ Parakeet Bed Clips for MakerGear 3D Printers We designed these low profile bed clips for use with our MakerGear printers The clips have a small beak that just reaches the glass bed to hold it in place. The "beak" that holds the...

PEI Print Surface Adhesive backed for easy application. Includes: PEI Sheet (1 pcs) Specifications:Material: ULTEM 1000Dimensions: 203*254 mm (8x10")Thickness: 175um Fits:MakerGear M2MakerGear M3 Notes:This is NOT a spring steel sheet.Tiny dots...

  Pinion Gear for MakerGear 3D Printers Goes on the extruder stepper motor shaft inside the gearbox. Fits:M2M3 SEM3 ID Use Loctite 609 to attach to motor shaft. Buy Loctite 609 here

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Specs:Wire:18 AGWLength: 72 inches (approximately) Max Operating Temp: 105°C (221°F)

PB Select™ RAMBo to LCD Smart Controller Adapter This is an unassembled kit that requires soldering to complete. Here is a picture of the assembled adapter for reference when soldering: RAMBO/Smart Controller Adapter assembled This...

Replacement SMD fuse for the RAMBo board on your MakerGear printer.

X/Y Stepper Motor for MakerGear 3D printers These motors are used to drive both the X and Y motion. Order 2 motors if you need to replace both axis.  Includes: Motor (1 pcs) Specs: 1.8° stepper motor with shaftx16 microstepping88...

MakerGear Z Stepper Motor with Leadscrew and Nut Includes: Z motor with integrated leadscrew (1 pcs)Leadscrew nut (1 pcs) Fits:M3 SEM3 IDM2 RevG or later (with black z motor) Note: The leadscrew nut on this latest batch is white, not black...

Super Lube® 82340 - Synthetic Grease with SYNCOLON™ (PTFE)  This small size pouch is great for lubing the filament drive gears on dual gear or orbiting gear extruders. Includes: 1 Pouch Size: 1 cc Contains no...

Super Lube 21010 - Synthetic Grease with SYNCOLON™ (PTFE)  Super Lube 21010 is a Prusa Research approved lubricant.   Use on your Bondtech drive gears, Linear bearings or anywhere else you need a high quality grease...