Prusa

Prusa Hotend PTFE Tube This is a replacement hotend PTFE tube. Includes: Hotend PTFE tube (1 pcs) Specifications:Length: 42.3 mm (tolerance +/- 0.2 mm)Inner diameter: 1.85 mmOuter diameter: 4 mm Fits:MK3S+MK3S+ with MMU2SMK3S+ with...

Pulley Motor Includes: Pulley motor (1 pcs) Specifications:Connector: MOLEX 50-57-9404Rated current: DC 1A Fits:MMU2SMMU3 To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow the manual for...

4mm Push Fit Collet (Collar) High quality replacement push fit collet with metal teeth.  Includes: Collet (1 pcs)  Fits: Bondtech ExtrudersE3D V6 HotendE3D Revo SixE3D Revo MicroE3D Revo CRPrusa i3 series Only fits: 4 mm PTFE Tube...

PC4-M8 Push Fit Connector For use with Capricorn or similar PTFE tubing. Includes: Push Fit Connector (1 pcs) Fits:Prusa MINIPrusa MINI+ Notes:The internal depth of this fitting is not as deep as the stock fitting, so you may need to...

RAMBo Mini Mainboard Please read our returns policy regarding electronic items This RAMBo Mini is made by Ultimachine in the USA and comes with the selected firmware pre-installed. This is a direct replacement for the stock mainboard. UltiMachine is...

PB Select™ Hardware Kit Includes:M3x16 - fan to fan duct (4 pcs)M3x10 pan head - to clamp heater (2 pcs)M3x4 set screw for thermistor (2 pcs)M2 hex wrench (1 pcs)M1.5 hex wrench (1 pcs) For:E3D V6Prusa i3RepRap

Revo™ High Flow Brass Nozzle The Revo High Flow Nozzle increases your setup's volumetric flow rate, enabling you to print faster. Revo High Flow maintains the exact same form factor as standard Revo Hotends. This means there is no need...

Revo™ Brass Nozzle Single Nozzle Includes: Revo nozzle of selected size (1 pcs)ORTriple pack includes: 1 each of 0.25, 0.60 & 0.80mm nozzles Fits: All E3D Revo hotends Notes: - You may need to adjust your Z offset when changing...

Revo™ HeaterCore Includes:Heater cartridge/thermistor (1pcs)Spring (1 pcs)Silicone boot (1 pcs) Notes: Choose the correct voltage and wattage for your application.Before installing please read the HeaterCore wiring best practices page from E3D...

Revo™ ObXidian Nozzles The Revo ObXidian is specifically designed for printing fibre-filled polymers. ObXidian’s copper alloy construction has a similar thermal performance to Brass, making it a true drop-in replacement. Just use the...

Heatsink for Revo™ Six Includes:Heatsink (1 pcs)Collet (1 pcs)Collet clip (1 pcs)

Revo™ Silicone Sock Pack Includes:0.25mm (2 pcs)0.4mm (2 pcs)0.6mm (2 pcs)0.8mm (2pcs)HeaterCore socks (2pcs) Fits: E3D Revo HeaterCore

Revo™ Spring Triple Pack Includes: Revo spring (3 pcs) These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo...

Screwdriver PH2 Screwdriver with a PH2 head. PH2 is the recommended standard for the screws used on Original Prusa Printers. Includes: Screwdriver (1 pcs) Specifications:Red Hand: PlasticScrewdriver length L1: 160 mmShank length...

Selector Motor for MMU2S/MMU3 Includes:Selector motor (1 pcs)Trapezoid nut (1 pcs) Specifications:Connector: MOLEX 50-57-9404Rated current: DC 1A Fits:MMU2SMMU3 To replace this part, please consult the Prusa Assembly Manuals. Make sure to...

M3x4 Set Screw (Grub Screw) Includes: Set screw (5 pcs) Size: M3x4mmGrade: 12.9Head Type: Hex Fits heater block of:E3D V6Prusa MK4Prusa XL Note: These are hex head set screws, not torx head (torx head is what comes standard on the MK4 and...

M3X4 Torx Head Set Screw Used on the Nextruder heater block Includes: M3x4 set screw (5 pcs) Note: Uses T6 Torx driver to install (not included) Fits:Prusa MK4Prusa XL

Prusa MMU2S-Einsy/Rambo signal cable Replacement MMU2S-Einsy/Rambo signal cable Includes: Cable (1 pcs) Fits the following printers with MMU2S:MK2.5SMK3MK3S To replace this parts, please consult the Prusa Assembly Manuals. Make sure to follow...

PB Select™ Silicone Sock Includes: Silicone sock (2 pcs) Color: BlackMax temperature: 280°c Fits:Prusa MK4Prusa XL

PB Select™ V6 Silicone Sock The primary purpose of a silicone sock is to help keep your hotend at a more consistent temperature, reducing the amount of times your heater needs to cycle. As an added benefit, the silicone sock will keep filament...