Robo R2

Robo R2/C2 Leadscrew Nut Includes: Nut (1 pcs)  Fits:Robo R2Robo C2

Robo 3D X/Z Axis Limit Switch  Includes: Limit switch (1 pcs) Fits: R2 Color of board may be different from picture  

Robo 3D Y Axis Limit Switch  I build these switches here at Partsbuilt 3D using quality JST connectors and genuine Omron or C&K switches. Includes: Limit switch (1 pcs) Fits: R2 Color of board may be different from picture 

Robo Z Axis Linear Bearing Includes: Bearing (1 pcs) Specifications:ID: 12mmOD: 21mmL: 57mmF: 32mm Fits:Robo R2Robo C2     

Robo Brass Bushing - 4 Pack Includes: Bushing (4 pcs) Specifications:ID: 8mmOD: 11.7mmL: 36mm Fits:Robo R2Robo C2

Robo R2 Linear Rod - 6mm for Inner X/Y Axis  Smooth linear rods for the Inner X/Y axis of the Robo R2.  Includes: Rod (1 pcs) G6 high precisionHRC60Hard Chrome PlatedGcr15 steel  Fits: R2

Robo R2 Linear Rod - 8mm for Outer X/Y Axis  Smooth linear rods for the outer X/Y axis of the Robo R2.  Includes: Rod (1 pcs) G6 high precisionHRC60 Hard Chrome PlatedGcr15 steel Fits: R2

Robo R2 Linear Rod - 12mm - Z Axis  Smooth linear rods for Z axis Includes: Rod (1 pcs) G6 high precisionHRC60 Hard Chrome Plated Gcr15 steel   Fits: R2 Z Axis

M2.3x6mm Blunt Nose, Pan Head Screw Set Includes: Screws (2 pcs) Head: PanSize: M2.6Length: 6mmType: Blunt nose

Robo 3D Brass Nozzle Size:  0.40mm  Fits: Robo R1Robo R1+Robo R2Robo C2

Nozzle Coat™  Nozzle Coat is a water-based PTFE nano coating for your nozzle & heater block. Using Nozzle Coat will help reduce the amount of plastic that sticks to the exterior of your nozzle & heater block. Includes:...

  Robo R2 BuildTak Print Surface Original Buildtak sheet Includes: Print surface (1 pcs) Fits: Robo R2 Notes:If you are printing with PETG, we recommend using a PEI print surface instead.Please Note: Care should be taken to check the Z...

  Original BuildTak Print Surface for Robo R2 Includes: Buildtak sheet (3 pcs) Fits: R2 Note:Works well with most filaments, however, for printing PETG, we recommend a PEI print surface.Care should be taken to check the Z height when changing...

Raspberry Pi Power Cable This is the cable that runs from the mainboard to the Raspberry Pi. It is a little shorter then the stock R2 cable, but will reach with slightly less excess wire. Includes: Cable (1 pcs) Fits:Robo R2Robo C2

Power Supply Cord AC power cord that runs from the power supply to a USA type wall outlet  Includes: Power cord (1 pcs) Note: Power supply is not included

Print Bed Plastic Housing for Robo R2 Includes: Plastic bed housing (1 pcs) Notes: This is the plastic housing only.Does not include screws: Reuse the screws from your old bed. Does not include magnets: Reuse the magnets...

Standoffs for Mounting Raspberry Pi Includes: Standoff (4 pcs) Fits:Robo R2Robo C2

Ribbon Cable - Uptown to Downtown Board  Includes: Cable (1 pcs) Fits:Robo R2Robo C2

  Micro-Swiss Wear-Resistant Nozzle with M6 Threads This M6 thread, Robo 3D style nozzle is made from a 360 brass base material and plated with TwinClad XT coating. TwinClad XT is a nickel composite coating designed for very low friction. It...

Robo R2/C2 Rubber Feet  Includes: Rubber foot (2 pcs)Installation pins (2 pcs) Fits: Robo R2Robo C2