Prusa

Prusa MINI+ Hotend Thermistor  *NOTE:  The MK2/2.5, MK3/S/+ and MINI/+ all use the same type of E3D thermistor.The MINI/+ thermistor has a longer wire (840mm on the MINI vs 750mm on the MK2/3 series). Therefore, this thermistor will...

Prusa MK4 Thermistor Kit for Heated Bed Includes:Heatbed thermistor E3D (1 pcs)Kapton tape (1 pcs)Aluminum tape (1 pcs) Fits:MK3.5MK3.9MK3.9SMK4MK4S To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow...

Prusa Thumb Screw M4x8 Includes: Thumb screw (1 pcs) Fits: Prusa CORE OnePrusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4S To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow the manual for...

PB Select™ GT Timing Belt Pulley Includes: Timing pulley T16-2GT (1 pcs)Grub screw (2 pcs) Size: Tooth count: 16Bore: 5mmFor belt width of: 6mm Fits:Prusa MK2Prusa MK2SPrusa MK2.5Prusa MK2.5SPrusa MK3Prusa MK3SPrusa MK3S+Prusa MK3...

Prusa Timing Belt Pulley Includes: Timing pulley T16-2GT (1 pcs)Grub screw (2 pcs) Fits:MK2MK2SMK2.5MK2.5SMK3MK3SMK3S+Prusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4SMINIMINI+ To replace this part, please consult the Prusa Assembly Manuals. Make...

Torx Driver Includes: Torx driver (1 pcs) Size: T6Shaft Length: 3 inchesOverall Length: 6 Inches Fits: Set screws in Nextruder heater block

Torx Driver Includes: Torx driver (1 pcs) Size: T8Shaft Length: 3 inchesOverall Length: 6 Inches Fits: Torx screw holding hall sensor to heatsink. 

PB Select™ U-Bolt Includes:U-bolt (1 pcs)Nylock nuts (2 pcs) Specifications:Thread: M3Length: 26 mmThread length: 7mmDistance between center of both tips: 20 mmInside bend diameter: 16.5mm Fits:MK2SMK2.5MK2.5SMK3MK3SMINI To replace this part,...

E3D V6 ObXidian Nozzle V6 nozzles are designed for use with the E3D V6 heater block. Use small nozzle orifices to achieve fine details or larger nozzle orifice sizes for more substantial, stronger 3D prints. Includes: Nozzle of selected size (1...

Washer 3x7x1 Replacement nylon washers for your Core XY subassembly. Includes: Nylon Washer 3x7x1 (30 pcs) Fits: Prusa XL To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow...

PB Select™ Wi-Fi Adapter ESP-01S for MINI+ (ESP8266 1MB) Fully compatible with the Prusa MINI+ & MK4. Use this wireless adapter to add Wi-Fi to your MINI+ & MK4. Once installed, you can send G-codes from your PC directly to the...

Prusa Wi-Fi Adapter Use this wireless adapter to add Wi-Fi to your printer. Once installed you can send G-codes from your PC directly to the printer, start & stop the print and also monitor the current status or temperatures. Includes: Wi-Fi...

  SLS X-Carriage kit for Prusa i3 MK3S Note: This X-Carriage kit is required to install the Bondtech Upgrade Kit for Prusa. This is very similar to the original X-Carriage Kit. The main difference is the 3D printed technology used to...

Prusa xBuddy Board  Important  This xBuddy board is compatible only with two-wire Power Panic (black & white wires). Check your cables, before you order this part. Includes: xBuddy board (1 pcs)Thermal pads (3...

Double-Sided Powder-coated PA Nylon Spring Steel Sheet for Original Prusa XL (Factory Second Read Below) This is a FACTORY SECOND product:It is rated as factory second due to cosmetic and visual defects only. The cosmetic and visual defects do...

xLCD Board Replacement xLCD board for the xLCD assembly. You need Firmware version 4.7.5 or newer for this display to work properly. See below, which printers are compatible. Includes: xLCD board (1 pcs)  Important Note: XL...

xLCD cable Replacement cable runs from xLCD to xBuddy board Includes: xLCD cable (1 pcs) Fits:Prusa MK3.5Prusa MK3.9Prusa MK3.9SPrusa MK4Prusa MK4S To replace this parts, please consult the Prusa Assembly Manuals. Make sure to follow...

xLCD Cable Replacement LCD cable for the Original Prusa XL Includes: xLCD cable (1 pcs) Fits: Prusa XL To replace this parts, please consult the Prusa Assembly Manuals. Make sure to follow the manual for your printer model.

xLCD PE Cable This is a replacement for xLCD PE cable Includes: xLCD PE Cable (1 pcs) More details:Connectors: 2x fastonLength: 1475 mm Fits: Prusa XL To replace this part, please consult the Prusa Assembly Manuals. Make sure to...

xLCD Plastic Parts (Case) Includes: Top case (1 pcs)Bottom case (1 pcs)Knob (1 pcs) Fits: Prusa MK4S To replace this part, please consult the Prusa Assembly Manuals. Make sure to follow the manual for your printer...