R1+ Parts

Pack of 2 BuildTak Original Sheets - 10x10  10x10 inches (254x254 mm) Creates an optimal bond between the 3D printed object and build surface Allows for clean and easy removal of the object from the build surface More durable and easier...

3mm Bed Magnets for R1/+ Glass Bed Please note: These magnets are 3mm thick and do not work with the latest v2.5 R1 bed, which requires 6mm magnets. Apply using epoxy and these clamps for best results. Sold in pack of 4  Fits: R1 and...

6mm Bed Magnets for R1/+ Glass Bed Please note: These magnets are 6mm thick, they work with both earlier beds and the latest v2.5 R1 bed, which requires 6mm magnets. Apply using this epoxy and these clamps for best results. Sold in pack of...

Ball Bearing Size: S608Z (8X22X7) Fits: Robo R1+ Prusa MINI Prusa MINI+ Prusa MMU2S

Robo R1+ X Axis Belt Fits: R1 and R1+ 

Robo R1+ Y Axis Belt  Fits: R1 and R1+ 

4 Position, 90 Degree Right Angle, Terminal Block Header Amps: 12 Pitch: 5.08mm  

Robo R1+ Heated Bed Connection Cable  If you currently have a V1 bed with a long cable, you will need this extension cable if you are upgrading to the v2 bed (which has a short cable). Buy the R1+ heated glass V2 bed here Fits: R1+ v2

Cable - Extruder Motor to Mainboard for Robo R1+ 

Power Supply Cable for Robo R1+ This cable runs from the power inlet to the power supply of the Robo R1+ Fits: R1+

SD to RAMPs cable Connects SD card reader to RAMPs board. Fits: R1 and R1+

Wire for X endstop limit switch Fits: Robo R1+

Type a description for this product here...

Wire for Z endstop limit switch Fits: Robo R1+

R1+ Fan Wire Runs from mainboard to print cooling fan. Will also work for the heatsink cooling fan, but the wires will need to be reversed or the fan runs backwards.  Fits: R1+

R1+ Thermistor Wire Runs from mainboard to thermistor Will also work for the heatsink fan or print cooling fan but the connector is not keyed so you need to pay attention to the orientation of the plug (at the mainboard) so the fan does not...

Robo R1/+ Bed Installation Clamps Small clamps to assist with the installation of bed magnets on the R1+ bed. Set of 4 clamps. These are 4 inch clamps with an opening of about 2 inches

  HARDMAN DOUBLE/BUBBLE 2 Part Epoxy - Very High Peel Strength  This is the epoxy we use for attaching the magnets to the R1/+ glass print bed. Full curing time is stated to be 7 days. However, when applying magentes to the R1 glass bed,...

Robo R1+ Extruder Axle Shaft  Fits: R1 and R1+

Robo R1+ Extruder Bracket  Fits: R1 and R1+ 

Robo R1+ Big Extruder Drive Gear  Fits: R1 and R1+ 

Robo R1+ Small Extruder Drive Gear Fits: R1 and R1+ 

R1+ Extruder Hardware Kit  This includes the screws, nuts, bolts, and springs needed for your R1+ extruder. Please Note: Does not include hobbed bolt, Axle Shaft or Idler bearing. These will need to be purchased separately. Fits: R1+

Robo Extruder Latch  Fits: R1 and R1+

Robo R1+ Bottom Cover Fan for Cooling Electronics This is the fan that cools the Arduino and RAMPs board in the bottom of the printer Amps: 0.08 Fits: R1+ Note: The color of the plug may differ from the photo above. 

Heatsink Fan for Robo 3D Printers This is the fan that cools heatsink (cold end) of the hotend assembly Fits: R1+  Note: The color of the plug may differ from the photo above. 

Robo R1+ Print Cooling Fan This is the fan that cools the part being printed. Amps: 0.08 Fits: R1+ Note: The color of the plug may differ from the photo above. 

Robo Fan Bracket  This is the bracket that holds the heatsink cooling fan Fits: R1 and R1+

Ferrite Core Anti-Interference Ring Fits wire up to 4mm

Robo R1+ Filament Guide Fits: R1 and R1+

254x254mm (10"x10") Replacement FlexPlate Please Note: This is not the Complete Builtak Flex System. This is a replacement FlexPlate and requires a magnetic mounting base and Builtak print surface. Specially-coated FlexPlates are resistant to...

BuildTak FlexPlate System for Printrbot Plus and Robo R1 - 10x10in Benefits: Easy print removal Better adhesion of prints with the BuildTak print surface Swap flexplates when a print is finished for more uptime (requires purchasing...

Precision Ground GT2 Stepper Motor Pulley These are recommended for use with Gates GT2/3 belts Includes Set Screw Fits: 5mm Motor Shaft Specs: 20 Tooth 7mm Wide (for 6mm belt) 5mm Bore

Robo R1+ Heated Glass Build Plate - New Style Important: Please read all the notes below before purchasing. If your current bed does not have the plug pictured, you also will need to purchase the R1+ bed connection cable here. This bed is made of...

Robo R1/R1+ Heater Cartridge Robo 3D replacement heater cartridge (also called heater core)

Robo R1/R1+ Compatible Heater Cartridge Extension Cable Extension cable for R1/R1+ heater cartridge  This cable has a plug on one end to plug into the R1/R1+ heater cartridge wire and bare wires (no plug) at the other end, so it will attach to...

Heatsink for Stepper Drivers Heatsink in silver aluminum to remove heat from desired component. Equipped with self-adhesive on the back for easy attachment.   Dimensions: 8.8 x 8.8 x 5 mm (+/- .15mm)

Robo Hobbed Bolt v2 This hobbed bolt has a wider filament path than the v1 (the v1 is no longer available). Fits: R1/R1+  Sold in units of one

Robo R1+ Hexagon Hot End Assembly For 1.75mm filament Includes: Complete Hotend12V Heater CartridgeThermistor0.40mm Brass Nozzle Note the proper routing of the hotend wires in the picture above. We recommend installing your hotend this way to...

Hotend Cable Guide for R1 Guides the hotend heater and thermistor cable When installing, rotate your hotend 90 degrees so the wires face the front of the printer. Designed by: Bob R.