Flashforge

Activated Carbon HEPA Filter Includes 1 complete filter Fits: Guider 2S

Flashforge Air Duct Fits: Guider 2 Air Duct only, does not include mounting screws.

Flashforge Air Duct Assembly Fits: Guider 2s HT

Flashforge Air Filter Includes: HEPA filter Filter Housing with magnets Fits: Adventurer 3

Micro Swiss All Metal Hotend Kit for Flashforge Finder/Inventor 2/Guider 2, 2S /Dremel 3D40 This is an all metal hotend upgrade kit for Flashforge Finder, Inventor 2 and Guider 2 printers Micro Swiss' all metal hotend allows you to print at much higher...

Flashforge V Bearing  Fits: Adventurer 3 Creator 3 Creator Pro Dreamer Dreamer 2 Finder 2.0 Guider 2 Guider 2S HT Inventor Inventor 2 Sold in units of 1

Flashforge Flange Bearing This is the bearing that goes on the inner side of the pulley on the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are needed per shaft

Deep Groove Ball Bearing for Flashforge Creator Pro Size: 5x8x2.5mm Fits: Creator Pro

Bearing Under Build Tray Size: 12x4x4 Fits: Adventurer 3 Compatible with: MP Voxel Robo E3

Bed Heater Flat Cable Fits: Adventurer 3 May Also fit: Monoprice Voxel and Robo E3D

Flashforge Bed Leveling Thumb Nut - 3 Pack Fits:  Inventor Inventor 2 Finder 2 Creator Pro Dreamer 2  

Flashforge Replacement Drive Belt Length: 860mm Fits: Creator Pro Sold in units of 1

Flashforge Replacement Drive Belt Length: 880mm Fits:  Dreamer Inventor Sold in units of 1

Flashforge Timing Belt  Size: 250mm Fits:  Creator Pro Dreamer 2 Finder 2 Inventor Inventor 2  

Flashforge Replacement Drive Belt Length: 590mm Fits: Creator Pro Dreamer Inventor

Flashforge Build Plate  Comes with print surface (build tape) pre-installed Fits: Adventurer 3

Flashforge Build Plate Assembly Comes with print surface (build tape) pre-installed Fits: Finder Finder 2

FlexSys™ Build Plate - double-sided textured PEI powder-coated flexible print surface  Powder coating directly on metal makes it very hard to damage this build plate. Powder coating also gives the surface a distinct textured look that will be...

Flashforge Build Plate Assembly Removable base plate with removable magnetic flexible plate. Comes with print surface (build tape) pre-installed Fits: Inventor 2

Flashforge Magnetic Build Plate Base Use with Flashforge flexible build plate (not included) Fits: Creator 3

Flashforge Flexible Spring Steel Build Plate System Includes Flashforge print surface pre-installed Magnet sheet with adhesive for easy installation  Spring steel flex print surface Fits: Creator Pro 2 Creator Pro Creator...

Flashforge Flexible Spring Steel Build Plate System Includes Flashforge print surface pre-installed Magnet sheet with adhesive for easy installation  Spring steel flex print surface Fits: Guider 2S HT  

Flashforge Build Plate Frame Fits: Guider 2S

Flashforge Glass Build  Fits: Guider 2S Guider 2 with plastic housing upgrade Note: If you are installing this glass build plate on a Guider 2 you will need to purchase the Guider 2S plastic build plate frame - Available here

Build Plate Heater for Flashforge Adventurer 3 Size: 164*168mm May also fit: Monoprice Voxel Robo E3

Flashforge PCB Build Plate Heater Fits: Creator Pro Dreamer 2 Inventor

Flashforge PCB Build Plate Heater Fits: Guider 2 Guider 2S HT

Flashforge Build Plate Latch/Handle No screws included Fits: Adventurer 3 Also Compatible with: MP Voxel Robo E3

Flashforge Bed Leveling Sensor Switch Fits: Creator 3

Flashforge Bed Leveling Sensor Switch This is the sensor only and does not include the arm or servo.  Fits: Guider 2 Guider 2S Finder 2 Inventor 2 Inventor 2S

Flashforge Extruder Motor Cable Fits: Creator Pro

Flashforge Extruder Motor Cable Length: 62cm Fits: Adventurer 3 Compatible with: MP Voxel Robo E3

Flashforge Filament Sensor Cable Fits: Adventurer 3 Compatible with: MP Voxel Robo E3

Flashforge LED cable Fits: Creator Pro Creator Max

Flashforge LED Cable Length:7cm Fits: Adventurer 3 Compatible with: MP Voxel Robo E3

Flashforge Extruder Motor Cable (wiring) For Left Extruder Motor Fits: Creator Max Inventor Dreamer    

Flashforge Hotend Cable (wiring) Left Hotend to mainboard This does not include the extruder motor cable. The left extruder motor cable is available here Fits: Inventor Dreamer    

Nozzle Heating Cable Length: 6cm Fits: Adventurer 3 Compatible with: MP Voxel Robo E3

Flashforge Extruder Motor Cable (wiring)  For Right Extruder Motor  Fits: Creator Max Inventor Dreamer 2    

Flashforge Hotend Cable (wiring) Right Hotend to mainboard. This does not include the extruder motor cable. The right side extruder motor cable is available here Fits: Inventor Dreamer