Flashforge OEM

Flashforge Extruder Stepper Motor Fits: Guider 2

Flashforge Flange Bearing This is the bearing that goes on the inner side of the pulley on the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are...

Flashforge Flange Bearing This is the bearing that goes on the end of the Y axis drive shaft. Fits: Dreamer Dreamer NX Inventor Sold in units of 1, two bearings are needed per shaft

Flashforge Idler Pulley Assembly For: Y-Axis Fits: Dreamer Dreamer NX Inventor

Flashforge 80X25mm Fan Volts: 24 Watts:  Chamber Fan Fits: Guider 2S

Flashforge 80X15mm Fan Volts: 24 Watts:  Chamber Fan Fits: Inventor

Flashforge 80X15mm Fan Volts: 24 Watts:  Chamber fan Fits: Dreamer

Flashforge Extruder Carriage (Bracket) Does not include bearings. Purchase the correct bearings here. Fits: Dreamer NX

Flashforge Finder 2.0 (24v) Extruder Assembly Includes timing belt pre installed Fits: Finder 2.0 (24 volt version)

Flashforge Replacement Drive Belt Length: 880mm Fits:  Dreamer Inventor Sold in units of 1

Flashforge 40x10mm Fan 24v, 0.08a   Fits: Dreamer 2 Inventor

Replacement Z Axis Stepper Driver Includes heatsink Fits: Guider 2S HT Sold in units of 1

Flashforge Dreamer 2 Mainboard  Written on board: Inventor Control Board V0.5 Comes with Flashforge firmware preinstalled Fits: Dreamer Note: Does not come with cables, SD card or...

Flashforge Replacement Spring 9.4x20 Bed leveling spring.  Fits: Dreamer Finder Inventor Creator Pro/Max

Front Door for Flashforge Inventor 2 Acrylic Comes with 2 Magnets Fits: Inventor 2

Front Door for Flashforge Dreamer and Inventor Acrylic Comes with 2 magnets pre-installed Fits: Dreamer Inventor (will not fit Inventor 2)

Flashforge Dreamer Z Motor with Leadscrew & Nut

Replacement Power Supply for 12 Volt Finder Fits: Finder (12 volt only)

Flashforge Linear Rod Axis: X Fits: Dreamer

Flashforge Linear Rod Axis: Y (front to back) Fits: Dreamer

Flashforge Bed Leveling Sensor Switch Fits: Creator 3

Flashforge Driven Shaft Size: 5x455mm Axis: Driven Y Axis Fits: Creator Pro

Flashforge Linear Rod Axis: X Fits: Creator Pro

Flashforge Hardened Steel Nozzle Orifice Size: 0.40mm This upgraded nozzle is more abrasion resistant for printing carbon fiber filled or other abrasive filaments. The thermal conductivity of a...

Flashforge Hardened Steel Nozzle Orifice Size: 0.60mm   This upgraded nozzle is more abrasion resistant for printing carbon fiber filled or other abrasive filaments.   The thermal...

Flashforge Filament Guide Tube Fits:  Guider 2 Guider 2S

Flashforge Filament Guide Tube Fits: Creator 3

Flashforge Timing Belt Belt for X Axis  Fits: Creator 3 Note: Item may differ from picture

Flashforge Timing Belt Belt for Y Axis  Fits: Creator 3 Note: Item may differ from picture

Flashforge Nozzle Assembly for Creator 3 Comes with 0.40mm nozzle Fits: Creator 3  

Flashforge Guider 2 Mainboard Fits: Guider 2  

Flashforge Unclog Pin 1.5mm Diameter Helps clear blockages from the hotend

Flashforge Guider 2S HT Mainboard Fits: Guider 2S HT  

Flashforge Bed Leveling Sensor Switch This is the sensor only and does not include the arm or servo.  Fits: Guider 2 Guider 2S Finder 2 Inventor 2 Inventor 2S

Flashforge LCD Touch Screen Fits:  Creator Max Dreamer Inventor  

Flashforge Creator Max Mainboard  

Hotend Mounting Block

Flashforge Heatsink Includes heatsink only Fits: Guider 2S

Flashforge Heatsink Includes heatsink only Fits: Guider 2

Flashforge Heatsink Includes heatsink only Fits: Finder Finder 2 Inventor 2 Inventor 2S